X10 Community Forum

📸Cameras & Camera Software => Legacy non Wi-Fi X10 Cameras => Camera General Discussion => Wireless Cameras(non IP) => Topic started by: halfelite on April 07, 2008, 04:56:22 AM

Title: cams wont cycle at all
Post by: halfelite on April 07, 2008, 04:56:22 AM
I have ben trying for hours to get this to work. I have the cameras set as a-1, a-2, a-3 one ninja and x2cams But it only shows a-2 it wont cycle at all if i unplug a-2 then it shows a-1 and never cycles if i click a-3 it shows the picture of a-1. What could i be doing wrong. And i saw mentioned there is a 4 cam reicever to display all 4 at one time but I couldnt find it anywere on x10 website. And i have tried ruling out interference.I see the cm1919a light blink everytime its supposed to change cams so i know its working.
Title: Re: cams wont cycle at all
Post by: halfelite on April 07, 2008, 05:58:27 AM
From more testing now it seems that it only displays the cam that is closest. i can unplung the closest one and it will only display the next closest. and so on. I have tried turning of my wirelss router,sonos music players,all cell phones,cordlesss phones its 3am now no tvs are on and all my neighbors should be sleeping so interference should be down. Ok brought all 3 cameras in the same room and noticed they camera in vanguard finally changed got up to go hit the scan button and noticed when i walk infront of a camera it no longer works and switched to a differnt one. Its only displaying the camera with the best signal.
Title: Re: cams wont cycle at all
Post by: -Bill- (of wgjohns.com) on April 07, 2008, 10:02:51 PM
halfelite,

The CM19A only sends X10 control signals by RF... the camera power supplies only receive X10 on / off signals from the power line (PLC).  You need a TM751 or some other RF to PLC transceiver to convert the signals so that the cameras switch on and off appropriately.  Otherwise, you will get just what you have observed... the "loudest" camera will show because they are all on at the same time.  That or all you will see is interference.
Title: Re: cams wont cycle at all
Post by: halfelite on April 07, 2008, 11:32:49 PM
Ok i see i thought the TM751 was to just control the outlet plug that is on itself. Man after all that i just needed to plug in the TM751 i feel dumb.
Title: Re: cams wont cycle at all
Post by: -Bill- (of wgjohns.com) on April 08, 2008, 09:37:11 PM
Ok i see i thought the TM751 was to just control the outlet plug that is on itself. Man after all that i just needed to plug in the TM751 i feel dumb.

No need to feel dumb.  Sometimes it's hard to see the problem when you're too close to it.

Glad to hear it works now!
Title: Re: cams wont cycle at all
Post by: tom j on April 15, 2008, 03:31:03 PM
halfelite,

The CM19A only sends X10 control signals by RF... the camera power supplies only receive X10 on / off signals from the power line (PLC).  You need a TM751 or some other RF to PLC transceiver to convert the signals so that the cameras switch on and off appropriately.  Otherwise, you will get just what you have observed... the "loudest" camera will show because they are all on at the same time.  That or all you will see is interference.

Really good looking out Bill! real nice of you to help! had to give you a + myself, even though it wasen't my problem. I think we give better support the tech support sometimes!  ;D

Tom j.
Title: Re: cams wont cycle at all
Post by: alamjones on May 04, 2008, 02:46:03 PM
I just purchased the wireless camera and have the TM751 but am still unable to get the camera's to cycle.  I am using the Ninja remote.

Quote from: -Bill- (of wgjohns.com) on April 07, 2008, 07:02:51 pm
halfelite,

The CM19A only sends X10 control signals by RF... the camera power supplies only receive X10 on / off signals from the power line (PLC).  You need a TM751 or some other RF to PLC transceiver to convert the signals so that the cameras switch on and off appropriately.  Otherwise, you will get just what you have observed... the "loudest" camera will show because they are all on at the same time.  That or all you will see is interference.

Really good looking out Bill! real nice of you to help! had to give you a + myself, even though it wasen't my problem. I think we give better support the tech support sometimes!  Grin

Tom j.