X10 Community Forum
🔌General Home Automation => Automating Your House => Topic started by: wyx2000 on August 14, 2011, 01:22:25 PM
-
this is for my garden's watering
-
Are you looking for a standalone type system or one that can be controlled by X10?
-
this is for my garden's watering
Gee Boomer, with no more guidance than that, here this will fill your requirements:
http://www.northerntool.com/shop/tools/product_200417997_200417997?cm_mmc=Google-pla-_-Grounds%20Maintenance-_-Sprinklers-_-212083
-
Are you looking for a standalone type system or one that can be controlled by X10?
One that can be controlled by X10, or let's say something that is controlled by AC switch
-
If you are looking for a system that can do up to eight zones.
http://www.wgldesigns.com/rain8.html
Or are you looking for some type of valve that can be turned On and Off? Maybe by an appliance module or if low voltage a Universal Module?
-
If you are looking for a system that can do up to eight zones.
http://www.wgldesigns.com/rain8.html
Or are you looking for some type of valve that can be turned On and Off? Maybe by an appliance module or if low voltage a Universal Module?
Yes, Iam looking for some type of valve that can be turned On and Off
-
I have seen all kinds of electrically controlled valves.
Some are made to turn off the whole house watter supply on a leak detection.
There are irrigation valves that are PVC and I believe are bonded to PVC pipes to form a watering network.
There maybe a few that can be screwed on to an outside faucet.
Most are controlled by 24 volts AC. X10 does not make a module that can do that directly. You could use a 24 volt transformer and control it by an appliance module, relay style wall switch like a WS13A or an in line module like a XPFM.
Another way would be the transformer is On all the time and you control the 24 volt AC side with a Universal Module.
Guess it may depend on how you want to connect the valve to the water supply.
Then figure out how to control it.
-
Seems to me.... someone was using the solenoids out of old washing machines for that.
-
It is me. Although I don't endorse the practice. I also harvest them out of dishwashers and refrigerators. I've even purchased them as replacement parts from my local appliance dealer ($15-$45).
Not the safest way to go. I'd consider a good enclosure and a GFI.
-
It is me. Although I don't endorse the practice. I also harvest them out of dishwashers and refrigerators.
Not the safest way to go. I'd consider a good enclosure and a GFI.
Knight, are these always 120V AC or do you see any 24V AC valves?
-
I have only seen 120 volt ones.
That said.
None of the washers I have seen. Have fancy electronic controlls. Just a timer run by a motor. ;D
-
I have only seen 120 volt ones.
Yeah, that is all I have come across also. I don't have an outlet near the hose bib, so have been looking for a low voltage valve that I can feed with a long run of bell wire. I may do like Knight suggested and just put a 120V valve in the basement, fed from a GFI.
-
I have only seen 120 volt ones.
Yeah, that is all I have come across also. I don't have an outlet near the hose bib, so have been looking for a low voltage valve that I can feed with a long run of bell wire.
24VAC solenoid valves for use with water
http://www.mcmaster.com/#standard-solenoid-valves/=dpz6w1
-
Yeah, that is all I have come across also. I don't have an outlet near the hose bib, so have been looking for a low voltage valve that I can feed with a long run of bell wire. I may do like Knight suggested and just put a 120V valve in the basement, fed from a GFI.
Gee, years ago all I did was get one of the 24V irrigation valves sold by Lowes or Home Depot, and used a couple of adapters to go from pipe thread to garden hose couplings. Then I just screwed it onto the outside faucet. For control I used a 24V "wall-wart" transformer plugged into an X10 appliance module, and ran the low-voltage wire out through a window. It took care of the garden just fine while we were out of town.
Jeff