Please login or register.

Login with username, password and session length
Advanced search  

News:

The Buster PiX10Hub is here! Created by the Community, for the Community.:)% #:)

Pages: 1 ... 7 8 [9] 10
 81 
 on: February 15, 2020, 03:28:01 PM 
Started by Moose - Last post by petera
That was a sequence of keys to get you out of the editor safely. Standby for the next post

 82 
 on: February 15, 2020, 03:25:23 PM 
Started by Moose - Last post by Moose
Well, I think I did what you asked.  ??? How do I know if I did it correctly?

Was the file empty

Yes, it was empty. What is the N supposed to do?

 83 
 on: February 15, 2020, 03:22:21 PM 
Started by Moose - Last post by petera
Well, I think I did what you asked.  ??? How do I know if I did it correctly?

Was the file empty

 84 
 on: February 15, 2020, 03:17:55 PM 
Started by Moose - Last post by Moose
Well, I think I did what you asked.  ??? How do I know if I did it correctly?

 85 
 on: February 15, 2020, 03:07:22 PM 
Started by Moose - Last post by petera
Ok itís clear from that output that HG CM19 XtenLib driver is trying to establish a connection to your CM19 and is failing. That would account for the frequent connected/disconnected messages and the fact that you are seeing no activity from the LED light on the CM19. At least thatís established.

This can be one of two things. Firstly and most likely is you have a faulty CM19. Secondly and quite possible too is that you have an issue with conflicting drivers trying to grab the same Com port. Standby for instructions on how to confirm the latter.

Ok in PuTTY copy/paste the following. You will be entering the editor so when you have finished make sure you press Ctrl-x keys and then the N key and press enter. Copy/paste the contents of this file

sudo nano /etc/modprobe.d/blacklist.conf

 86 
 on: February 15, 2020, 02:56:56 PM 
Started by Moose - Last post by petera
Ok itís clear from that output that HG CM19 XtenLib driver is trying to establish a connection to your CM19 and is failing. That would account for the frequent connected/disconnected messages and the fact that you are seeing no activity from the LED light on the CM19. At least thatís established.

This can be one of two things. Firstly and most likely is you have a faulty CM19. Secondly and quite possible too is that you have an issue with conflicting drivers trying to grab the same Com port. Standby for instructions on how to confirm the latter.

 87 
 on: February 15, 2020, 02:09:11 PM 
Started by Moose - Last post by Moose
pi@raspberrypi:~ $ sudo systemctl status homegenie.service
● homegenie.service - Homegenie server
   Loaded: loaded (/etc/systemd/system/homegenie.service; enabled; vendor preset: enabled)
   Active: active (running) since Sat 2020-02-15 14:08:12 EST; 17s ago
 Main PID: 18565 (mono)
    Tasks: 59 (limit: 2200)
   Memory: 58.2M
   CGroup: /system.slice/homegenie.service
           └─18565 /usr/bin/mono /home/pi/homegenie/HomeGenie.exe --log

Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Cm19Manager.ReaderTask () [0x00008] in <a99ee7f64cb6456ca801bb9
Feb 15 14:08:22 raspberrypi mono[18565]: 2020-02-15 14:08:22.4468 Error System.Exception: Submit Async Read Failed.
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Driver.CM19.ReadData () [0x00029] in <a99ee7f64cb6456ca801bb9af
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Cm19Manager.ReaderTask () [0x00008] in <a99ee7f64cb6456ca801bb9
Feb 15 14:08:22 raspberrypi mono[18565]: 2020-02-15 14:08:22.4468 Error System.Exception: Submit Async Read Failed.
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Driver.CM19.ReadData () [0x00029] in <a99ee7f64cb6456ca801bb9af
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Cm19Manager.ReaderTask () [0x00008] in <a99ee7f64cb6456ca801bb9
Feb 15 14:08:22 raspberrypi mono[18565]: 2020-02-15 14:08:22.4468 Error System.Exception: Submit Async Read Failed.
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Driver.CM19.ReadData () [0x00029] in <a99ee7f64cb6456ca801bb9af
Feb 15 14:08:22 raspberrypi mono[18565]:   at CM19Lib.Cm19Manager.ReaderTask () [0x00008] in <a99ee7f64cb6456ca801bb9

Please keep in mind that HG is still only connected about 10 sec. in every 2 minutes.

 88 
 on: February 15, 2020, 02:04:03 PM 
Started by Moose - Last post by petera
Ok from the checks you have carried out HG is not your problem.

One more check you need to carry out. While HG is running unplug the CM19 and plug it back into the Pi. Immediately go to PuTTY and type

sudo systemctl status homegenie.service

and paste the results.

 89 
 on: February 15, 2020, 01:53:46 PM 
Started by Moose - Last post by Moose
Iím not familiar with that but it may use the same protocol as the CM11 although the device id could be an issue.

When your CM19 is plugged into the Pi does the Led remain lit.
No I have never seen the CM19 led on or flash.

 90 
 on: February 15, 2020, 01:43:15 PM 
Started by Moose - Last post by petera
Iím not familiar with that but it may use the same protocol as the CM11 although the device id could be an issue.

When your CM19 is plugged into the Pi does the Led remain lit.

Pages: 1 ... 7 8 [9] 10
X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.