Please login or register.

Login with username, password and session length
Advanced search  

News:

The X10Hub (PiX10Hub) is here! Created by the Community, for the Community.:)% #:)

Author Topic: "Warning - Your Pro system is nag nag nag nag nag nag nag"  (Read 11861 times)

PaulBennett

  • Jr. Member
  • **
  • Helpful Post Rating: -2
  • Posts: 10
"Warning - Your Pro system is nag nag nag nag nag nag nag"
« on: February 07, 2007, 04:45:20 AM »

"Warning - Your ActiveHomePro system has the iWitness Plugin installed and registered but ActiveHomePro is unable to connect to the USB Device."

I bought the whole software pack under pressure but don't like the camera capture feature..   

I am frustrated getting this nag message which greatly slows my use of the software.   How do I get rid of this message?

ActiveHome Pro sucks

Logged

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: "Warning - Your Pro system is nag nag nag nag nag nag nag"
« Reply #1 on: February 07, 2007, 09:49:59 AM »

Calm down, Paul.

This is a common problem, and a search by you would have found the cure. But, here it is:

1. Unplug the CM15A from the outlet.
2. Remove the batteries.
3 Wait five minutes.
4. Shut the computer down.
5. Replace the batteries in the 15 and plug it back in the outlet.
6. Reboot the computer. When Windows loads, you should hear a "beep", which says Windows has found a new device.
7. Open the Control Panel, click on System, then click the hardware tab. Scroll down to Universal Serial Bus Controller s, you should see "X10 USB Active Home (ACPI-compliant"
8 open AHP, you should not get any odd messages.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 264
  • Posts: 9423
  • I don't work for X10, I use it successfuly!
    • Tuicemen Software
Re: "Warning - Your Pro system is nag nag nag nag nag nag nag"
« Reply #2 on: February 07, 2007, 02:42:12 PM »

Actualy you don't Have to do all that Dan!
And most times that won't work As windows sees the intel cam driver instead!
But this will fix the problem Paul: Topic: VA11A does not work  (Read 11563 times)   provided of coarse you have a VA11A and it is pluged in!
If you don't you'll have to save your AHX file then reinstall the software but don't add the iwitness plug-in since you don't like it anyways! ;) :D ;D
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

Find extra info @ My forum

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: "Warning - Your Pro system is nag nag nag nag nag nag nag"
« Reply #3 on: February 07, 2007, 03:06:42 PM »

The Intel Camera problem was NOT what Paul had, it was AHP's inability to see the CM15.

What I posted was the fix for that.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 264
  • Posts: 9423
  • I don't work for X10, I use it successfuly!
    • Tuicemen Software
Re: "Warning - Your Pro system is nag nag nag nag nag nag nag"
« Reply #4 on: February 07, 2007, 03:21:02 PM »

Quote
"Warning - Your ActiveHomePro system has the iWitness Plugin installed and registered but ActiveHomePro is unable to connect to the USB Device."
Dan
When You get this message the problem is the VA11A as it is a USB device as well! ;) :D
If you had that plug-in you'd Know that! ;)
But you are right! What you thought was the problem, is a common problem, As is the VA11A!
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

Find extra info @ My forum
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.