Please login or register.

Login with username, password and session length
Advanced search  

News:

The X10Hub (PiX10Hub) is here! Created by the Community, for the Community.:)% #:)

Author Topic: Interesting Powermid Problem  (Read 20043 times)

deppeler

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 1
Interesting Powermid Problem
« on: April 02, 2007, 03:21:27 PM »

I bought a set of Powermid receivers/transmitters so I could control my Hauppauge WinTV card whilst watching it on the TV. I set the transmitter on the TV and the receiver at the computer.
I the Hauppauge remote (Silver 45 button) that came with the TV card to control it and I use my RCA Universal remote to control the TV.
It all works fine accept that when I use my RCA Universal remote as follows:
*If I turn off the TV, it starts the Radio application (part of the Hauppauge software) on the PC
*If I select Prev Channel it brings up the windows task list on the PC

Seems the Powermid is transmitting commands to the PC.
This is very annoying but for the time being I'm just unplugging the Powermid transmitter on the TV so I can use the TV's remote without this happening until I need to control the PC.

Have others had similar experiences like this?

thanks
Paul
Logged

MichaelC

  • Hero Member
  • *****
  • Helpful Post Rating: 36
  • Posts: 151
Re: Interesting Powermid Problem
« Reply #1 on: April 02, 2007, 05:09:36 PM »

If I recall correctly, the Hauppauge TV remote and receiver are made by X10. It sounds like maybe some of the RF that is sent between PowerMIDs matches the RF format of the receiver, either by design or by accident. I'm not sure what can be done about that.
Logged

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 174
  • Posts: 6853
Re: Interesting Powermid Problem
« Reply #2 on: April 02, 2007, 06:44:15 PM »

From what I have heard, it's not that unusual to have conflicting IR signals, particularly with crossed branded equipment.

The easy solution, is to place your Powermid [transmitter] slightly out of range (like off to the left a little) from where you point the RCA remote you use to control the TV. Then when you use the Hauppauge remote (Silver 45 button), point to towards the Powermid [transmitter].

Logged
New ideas for marketing Smarthomes may alter the Home Automation world completely.... and forever.

Oldtimer

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 45
  • Posts: 364
  • Line Noise & Signal Sucker Fatigue Syndrome
    • Oldtimer's X10 Forum Home Page
Re: Interesting Powermid Problem
« Reply #3 on: April 05, 2007, 03:19:21 PM »

We've used a Powermid off & on with different equipment for many years and have always had to work around a problem similar to yours.  When we first installed it we had Sony Trinitron monitor receivers both upstairs and downstairs.  Even though they were manufactured several years apart the remote controls were interchangeable for the basic functions.  Although the Powermid was only intended to operate a VCR upstairs from downstairs, the upstairs TV kept responding to the downstairs control until we turned the downstairs Powermid so that its front/sensing surface was facing the wall in a bookcase.  Then when we wanted to remote control the VCR we just turned the Powermid around so it faced forward.

When we switched over to a DVD player downstairs we temporarily retired the Powermid for several years.  It was put back into service again when we got a second Tivo box upstairs with an optional  feed to the downstairs TV.  Since both Tivo remotes were identical we were faced with the same problem again but with a new twist.  Now if either Tivo got turned on unitentionally by the downstairs control while you were operating the other there was the additional possibility that you could also accidently erase a recorded program on one Tivo while erasing a program on the other. Simply reversing the Powermid wouldn't solve this problem.

Here's the final solution.  First I put a switch box and pilot light in a small box attached to the bottom of the Powermid.  You can't see it in the picture but it's about twice as deep as it is wide so it's quite stable.



Next I fabricated an IR blocker to cover the IR port on the downstairs Tivo.  It's a piece of bent aluminum with foam rubber on the back.  Here's a picture of it with the Tivo IR port exposed.  It's the small black rectangle to the right bottom of the Tivo face plate.



Here's a picture of the it with the Tivo IR port covered.



Since the upstairs Tivo/TV connection is composite video and the downstairs Tivo/TV connection is S-Video the RF coax output of the upstairs Tivo is available to loop through the VCR for recording and from that via coax to the downstairs TV set which does the input switching.  The S-video on the upstairs Tivo connects directly to my computer to burn DVDs. There is a composite video switch upstairs if you want to see output from the VCR on the upstairs TV, and you have to move a couple of jumpers to dub video tape to DVD on the computer.

It all seems to work very well except it mystifies my wife, which is alright with her since she has never needed to use it by herself since the feed to downstairs is mainly used to watch one of my programs that I've Tivoed upstairs.
« Last Edit: October 20, 2009, 10:31:21 PM by Oldtimer »
Logged
Having "fun" with X-10 since 1980.

TakeTheActive

  • Hero Member
  • *****
  • Helpful Post Rating: 126
  • Posts: 1047
  • Old !@#$% Tinkerer!
Re: Interesting Powermid Problem
« Reply #4 on: April 05, 2007, 04:25:53 PM »


We've used a Powermid off & on with different equipment for many years...

...Here's a picture of the it with the Tivo IR port covered.

Although I don't even own a Powermid myself, I *DO* know the amount of time and effort it took to compose this excellent reply.  And for that reason alone, I just gave you another Helpful!

Well done!

Thank you! :)

P.S. to Duck69 - Per my recent PM to you, THIS is how it's done... ;)
Logged
Low Post Count != Low Knowledge - High Post Count != High Knowledge ;)

ADVICE TO X-10 NEWBIES FROM AN X-10 OLD-TIMER
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.