Please login or register.

Login with username, password and session length

Author Topic: Transceiver working?  (Read 5891 times)

manetherin

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Transceiver working?
« on: November 06, 2008, 08:18:49 AM »

I just bought a 3 camera system and am trying to hook it up. I can't seem to switch between cameras. The only way to see one camera is to unplug the others. They are set up as A1, A2, and A3. My transceiver (CM19A) is powered by USB, but the light doesn't come on. Is the light supposed to be on? I'm wondering if I got a bad transceiver...
Logged

Jsnlong

  • Hero Member
  • *****
  • Helpful Post Rating: 17
  • Posts: 351
    • XKAR
Re: Transceiver working?
« Reply #1 on: November 06, 2008, 02:31:33 PM »

I dont know alot about the cams but from what I hear........

If you want to look at cam A1 then you have to shut off A2 and A3. Power can only be on to one camera at a time. That might help but may be not lol.

Good Luck
Logged
People are afraid of robots taking their jobs......The same jobs they complain all day about doing!!

Join the chat at http://www.bdshost.com/ac/

Coach of XKAR
Xenia Kids And Robots
www.xkar.org

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Transceiver working?
« Reply #2 on: November 06, 2008, 02:45:41 PM »

I just bought a 3 camera system and am trying to hook it up. I can't seem to switch between cameras.

The only way to see one camera is to unplug the others. They are set up as A1, A2, and A3.


The default position for cameras are ON. so just plugging-in the camera turns it ON. By setting the cameras in a group of 4 (as you have) sending an ON signal to ether of the A1, A2, or A3 House/Unit codes will turn other cameras in the same group OFF.


My transceiver (CM19A) is powered by USB, but the light doesn't come on. Is the light supposed to be on? I'm wondering if I got a bad transceiver...


Did you get a software download? Or a link to software in your confirmation email? Is the software running.... is the CM19A setup? Sending an ON signal to any one of the three cameras (in the group of four) should turn OFF the other two.
Logged
Home Automation is an always changing technology

manetherin

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Re: Transceiver working?
« Reply #3 on: November 06, 2008, 06:03:23 PM »

If I unplug the transceiver and then plug it back in it says:
 "X10 USB Firecracker Interface (ACPI-compliant) installed
The software for this device has been successfully installed."

Still no light on the transceiver...

If I use the remote to turn off camera 1, the name changes on the program, but it's still camera 1 that I'm getting a picture from.

confused...
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Transceiver working?
« Reply #4 on: November 06, 2008, 06:59:12 PM »

The CM19A sends and receives X10 RF signals. The cameras need a powerline signal to turn them on and off. Did you get anything else with the cameras. Like a TM751 or a power line controller?
The CM19A can control the Pan and Tilt functions of that type of mounts.
So with no power line signals all will default to ON and closets one will probably win.
Logged

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Transceiver working?
« Reply #5 on: November 06, 2008, 08:23:59 PM »

..... The cameras need a powerline signal to turn them on and off.

OMG what was I thinking.
Logged
Home Automation is an always changing technology
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.