Please login or register.

Login with username, password and session length

Author Topic: SMOKE ALARM for Home Security Systems  (Read 14536 times)

hummelbill

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 1
SMOKE ALARM for Home Security Systems
« on: July 13, 2011, 12:55:29 PM »

Are there others like me who would like SMOKE ALARMS for their Home managed through the X10 Security Systems.  Please Voice you agreement so X10 can get designing and delivering.  How can you have a motion detection and door opening alarm and not offer smoke detection?  Makes no sense to me.  Smoke alarms are as important as motion or doors/windows.   Please provide your agreement or disagreement.  Thanks  -:) -:) -:) -:)
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: SMOKE ALARM for Home Security Systems
« Reply #1 on: July 13, 2011, 02:20:02 PM »

Please Voice you agreement so X10 can get designing and delivering.  
rofl  You are new here aren't you?

The X10 Product Wish List does nothing more than take up space on the forum. It sounds good, but X10 does not react to suggestions. My point here to tell you to not get your hopes up. This request has been common since the forum was first started. Anywho, we ain't seen one yet.

Relative to that, there are a number of posts on this forum on adding smoke and CO3 detectors to the DS10 (even easier to add to a DS12A). You can search the forum but if you have DS12A it as simple as finding smoke and/or CO3 detectors with a contact closure output.

http://www.homecontrols.com/GE-Security-Photoelectric-Smoke-Detector-wRelay-and-Battery-Backup-GE350CX
http://www.selectsafetysales.com/p-217-kidde-smoke-alarm-relay-module-sm120x.aspx
Or "roll your own".
http://www.edcheung.com/automa/smoke_det.htm
« Last Edit: July 13, 2011, 02:42:50 PM by dave w »
Logged
"This aftershave makes me look fat"

luke03

  • Sr. Member
  • ****
  • Helpful Post Rating: 1
  • Posts: 83
Re: SMOKE ALARM for Home Security Systems
« Reply #2 on: July 20, 2011, 01:59:28 PM »

Dave W, great link. I like the idea of DIY to have an opto isolation IC then interface it with your existing system.
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: SMOKE ALARM for Home Security Systems
« Reply #3 on: July 20, 2011, 03:44:44 PM »

Dave W, great link. I like the idea of DIY to have an opto isolation IC then interface it with your existing system.
Yeah, optos make it easy to interface to just about anything with some diodes and resistors. I have not tried an opto with a Powerflash, but I think Brian H has tried an opto output directly across a PowerFlash with success. (i.e no additional power supplies). So all you need to engineer is the opto's input trigger.
Logged
"This aftershave makes me look fat"

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: SMOKE ALARM for Home Security Systems
« Reply #4 on: July 20, 2011, 06:33:12 PM »

The only thing you have to watch with a solid state device is the polarity.
The + mark on the Powerflash case is the polarity for a DC input.

When in the dry contact input. The internally generated sensing voltage - is on the terminal marked + and sensing voltage + on the terminal marked -.  ;D

My ELK930 Doorbell Sensor didn't work until I found the polarity reversed. As it uses a opto output and steals the power to run it from the sensing voltage of the Powerflash Module.
« Last Edit: July 20, 2011, 07:14:02 PM by Brian H »
Logged

aptalca

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 35
Re: SMOKE ALARM for Home Security Systems
« Reply #5 on: July 28, 2011, 01:48:18 PM »

Check out this thread: http://forums.x10.com/index.php?topic=24104.0

I just followed it with a couple changes you can see in my post on that thread.

It was very easy and total cost under $20 including the smoke alarm
Logged

remrick

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Re: SMOKE ALARM for Home Security Systems
« Reply #6 on: August 09, 2011, 09:33:21 PM »

DIY smoke alarm to a X10 door sensor at:

http://www.yourhouse2.com/X10smoke.html

Click the link to see schematic.

Cost under $10 +smoke det. +X10 door/window module DS10A
Later..
  Rian  -:)

NOTE I WOULD RECOMMEND THAT IF YOU DO THIS TO NOT USE THIS SMOKE DETECTOR AS YOUR ONLY DETECTOR.  INSTEAD PUT THIS MODIFIED ONE RIGHT NEXT TO YOUR REAL ONE.  BY DOING THIS YOU ARE MODIFYING THE DETECTOR AND IF YOU EXPERIENCE A FIRE AND THE DETECTOR DOES NOT WORK IT COULD BE SAID IN COURT/INSURANCE PURPOSES THAT YOU DAMAGED A WORKING PRODUCT AND THUS IT DID NOT WORK.  SO INSTEAD USE THIS IN ADDITION TO YOUR UNMODIFIED DETECTOR ONLY!
« Last Edit: August 10, 2011, 01:23:12 AM by remrick »
Logged

TVRUK

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Re: SMOKE ALARM for Home Security Systems
« Reply #7 on: September 01, 2011, 06:39:10 AM »

You're not trying to tell me that the UK finally HAS eomething the US doesn't - Are ya????

Smoke detector SD18:-

http://www.letsautomate.com/12713.cfm?CFID=2356042&CFTOKEN=18539de-359e2037-ecbf-4c86-a52f-3c56152f35a5

Circa $40 'ish


Well I never.....


Regards,

Trevor

PS: X10 EUROPE - SUCKS!, what a crock.... B:(
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: SMOKE ALARM for Home Security Systems
« Reply #8 on: September 01, 2011, 11:08:25 AM »

You're not trying to tell me that the UK finally HAS eomething the US doesn't - Are ya????

Yeah.
I think you also have a X10 touch screen controller also, don't you?

Now we need to find a way of converting your stuff to be compatable with our stuff!  rofl
Logged
"This aftershave makes me look fat"
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.