Please login or register.

Login with username, password and session length

Author Topic: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50  (Read 1497 times)

horstuff

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« on: July 02, 2020, 02:51:03 PM »

The old 50 panel was hooked up to the PSC05 and it all worked fine... it just turned on the outside lights whenever the alarm went off. I changed the old panel to a new Vista 20P, and I can't see how to wire the X10 to the new panel. The old panel had a 9 pin bus, the new panel has an 8 pin bus (7 if you include the missing pin 2), and I cant make sense of anything in the 20P instructions on how to wire it.

The phone jack on the X10 was wired thusly to the old 50 panel (and Im not at all sure the pigtail used on the 50 was the proper pigtail to use, maybe they just used whatever they had laying around)...
position 1 black was wired to the yellow and white wires on the 50 pigtail
position 2 red and position 3 green was wired to the black on the 50 pigtail
position 4 yellow was wired to the green on the 50 pigtail

Anybody out there know how to make this PSC05 work with a Vista 20P? Again, all it needs to do is turn on the lights when the alarm goes off (and I assume it would also turn off the lights when the alarm was disarmed / silenced).
Logged

brobin

  • Hero Member
  • *****
  • Helpful Post Rating: 157
  • Posts: 1406
Re: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« Reply #1 on: July 02, 2020, 08:30:11 PM »

From page 2-6 of the installation manual: bit.ly/2BxBray

Logged

horstuff

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« Reply #2 on: July 08, 2020, 02:00:03 PM »

Thanks, Ill try that. Sorry for the delay, been gone a few days
Logged

horstuff

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« Reply #3 on: July 08, 2020, 02:09:38 PM »

Would you be able to give me tips to program this? I think I will need to do a couple areas of programming... Im a newb at all this. Thanks very much.
Logged

brobin

  • Hero Member
  • *****
  • Helpful Post Rating: 157
  • Posts: 1406
Re: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« Reply #4 on: July 08, 2020, 05:30:57 PM »

Print this out and look at page 14 for X10 programming:

http://site.aesecurity.com/Manuals/v15pand20pprogrammingguide.pdf

The first pages show you how to enter programming mode.  I haven't worked on a Vista 20 in probably 20+ years so I don't remember much about the ins & outs but it's pretty straightforward and not much different from the Caddx N8-E that I use.

I think you'll find this page helpful too as it's more of a tutorial:

http://cocoontech.com/forums/page/articles/_/tutorials/home-security-tutorials/control-x10-upb-with-honeywell-ademco-vista-alarm

« Last Edit: July 22, 2020, 12:25:00 PM by brobin »
Logged

horstuff

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: X10 Pro PSC05 wiring to a Vista 20P from an old Ademco 50
« Reply #5 on: July 22, 2020, 12:01:14 PM »

Thank you thank you thank you :-)
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.