Please login or register.

Login with username, password and session length

Author Topic: Montion Sensor Turned Self Off When The Light Comes On  (Read 12513 times)

steve

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Montion Sensor Turned Self Off When The Light Comes On
« on: November 22, 2005, 06:31:11 PM »

Hello:

I noticed this about the motion sensors:

If I set it to only send the On signal when
the surronding is dark, and someone
triggers the sensor, the light comes on as
it should, but the sensor sees the light
and turns itself off.  The result is once
the light is on, it will not go off because
the sensor is off.

I have dealt with in one location where the
sensor is tucked in a corner where the
light won't reach, but I have other places
where it is not feasible.

How does everyone else deal with the
problem?  Thank you.

Steve
Logged

steve

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 19
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #1 on: November 29, 2005, 12:01:07 AM »

Anyone?
Logged

x10 nut

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 5
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #2 on: November 29, 2005, 11:15:15 AM »

What do you have the time-delay for the OFF
command set for? Default is 1 minute.
Logged

steve

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #3 on: November 29, 2005, 11:21:15 AM »

I have tried it on 1 minunte, 2 minutes and
4 minutes.  I get the same result each time.
Logged

x10 nut

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 5
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #4 on: November 29, 2005, 01:20:24 PM »

Try this.....
Walk into the room to activate the motion
sensor. Then stand directly in front of the
motion sensor. STAY ABSOLUTELY STILL! The
sensor checks for motion every 10 seconds,
and sends an ON command every time it sees
motion. After the time delay is up, you
should see the little red LED on top of the
motion sensor flicker as it sends the OFF
command to turn off the light. If you see
the OFF command being sent, and the light
does not respond, you'll need to find out
why.

Just out of curiosity, why do you have it
set to only sense during darkness? Is this
inside or outside?
Logged

tommy

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 14
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #5 on: November 30, 2005, 08:47:15 PM »

I'm just getting into X10 but I'm thinking
that if it is set to only sense during
darkness when the light goes on doesn't
that = not dark so no more sensing takes
place so that = no turn off command? I'm
just guessing but I find that if I put to
much thought into troubleshooting it is
harder than it seems.
Logged

x10 nut

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 5
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #6 on: December 01, 2005, 11:11:22 AM »

Tommy,

The "dark-only" setting is for the ON
commands only. After motion is detected, the
time delay starts. After the timer is up
(and no motion was detected), the motion
detector sends the OFF command, regardless
of light in the room. If motion is detected
again, the motion detector sends another ON
command, and the timer restarts.
Logged

tommy

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 14
Re: Montion Sensor Turned Self Off When The Light Comes On
« Reply #7 on: December 01, 2005, 02:51:49 PM »

X10 Nut - Thanks for that info.!  I'll
remember that when I start to use motions
sensors.
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.