Please login or register.

Login with username, password and session length

Author Topic: Controlling LED Christmas Lights  (Read 8633 times)

marv

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Controlling LED Christmas Lights
« on: December 08, 2005, 08:38:16 PM »

Hi,

Has anyone figured out a way to control
LED Cristmas lights.

I tried a lamp, appliance and the receptical
modules and they all left part of the lights
on dimly when turned off.

Any ideas?

I wam going to try a relay and see if that
works

Thanks

Marv
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Controlling LED Christmas Lights
« Reply #1 on: December 09, 2005, 06:56:25 AM »

An appliance and lamp modules have the local
sensing circuit in it and will keep the low
current leds on dimly. The relay turned on
and off by the X10 module should work. I
would use a 120 volt coil relay and an
appliance module. The other fix is remove
the sensing circuit in the module. There are
hacks that show how to do it. Also some
other brand X10 compatible modules have a
much lower sensing current that maybe better
with those led lights. X10 would say put a
small 7 watt night light on the same output
of the module as the led lights are
connected to.
Logged

aaron

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
Re: Controlling LED Christmas Lights
« Reply #2 on: December 13, 2005, 07:29:22 PM »

I just tried adding a nightlight to my
module's output, and still see the LED lights
when the module is switched off.  And this is
an appliance module that I'm using.

I *love* the LED xmas lights.  I guess I need
to go hack a module!
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Controlling LED Christmas Lights
« Reply #3 on: December 14, 2005, 06:34:22 PM »

http://www.idobartana.com/hakb/index.htm Is one place that shows mods. Note there are two mods for local sensing. The small jumper disables the sensing but the current is still there. The cut the diode top stops the current. As always you mod it is yours.
« Last Edit: October 24, 2009, 01:46:12 AM by -Bill- (of wgjohns.com) »
Logged

LeeBear35

  • Newbie
  • Helpful Post Rating: 1
  • Posts: 2
Re: Controlling LED Christmas Lights
« Reply #4 on: October 09, 2006, 12:32:35 PM »

I found the schematic for the lamp module listed on one of the replies above. The common alteration to remove local control is to clip the D10 diode that allows the signal to feed into the control chip. This leaves the current sensing circuit in place causing the 1.4v drop over the LED string to light the lamps when the module is off.

If you clip the 100K and 330K 1/2 watt resisters then the current sensing look is disabled on the lamp module. This also disables the Local control, you can replace these two resisters, but I have not computed the required values to ensure that all types of LED strings are off.

Anyhow the resisters are the larger ones in the circuit and they both have a common connection with the Triac to the output of the lamp module.
 :)
Logged

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Controlling LED Christmas Lights
« Reply #5 on: October 20, 2006, 11:08:58 PM »

Have you tried a socket rocket? Screw in a plug adapter, and plug in the lights.
« Last Edit: October 22, 2006, 10:40:04 PM by Dave_x10_L »
Logged
Home Automation is an always changing technology
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.