Please login or register.

Login with username, password and session length

Author Topic: Just does not want to work  (Read 4645 times)

robandcathy

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 6
Just does not want to work
« on: August 15, 2006, 08:58:44 PM »

I have the macro function, with the eagle eye sensor on D1 I set that to my trigger and the first line is to turn on B2 Front door light wait 5min and then off, I look in my activity monitor and see that D1 is received but I never see the B2 ON signal sent, does anyone why? from my remote B2 works fine also the sensor has fresh batt. so I'm sure the signal is good
Logged

JMac

  • Hero Member
  • *****
  • Helpful Post Rating: 23
  • Posts: 462
Re: Just does not want to work
« Reply #1 on: August 15, 2006, 10:41:59 PM »

Try a one second delay in the macro before B1 activation.  This worrked for me in a similar situation
Logged

JMac

  • Hero Member
  • *****
  • Helpful Post Rating: 23
  • Posts: 462
Re: Just does not want to work
« Reply #2 on: August 15, 2006, 10:42:58 PM »

I meant before the B2 ON activation
Logged

jawaid

  • Sr. Member
  • ****
  • Helpful Post Rating: 1
  • Posts: 84
Re: Just does not want to work
« Reply #3 on: August 16, 2006, 11:00:44 PM »

Do you see a 'B2 ON' being sent if you manually activate the B2 module from the AHP GUI?
Logged

-Bill- (of wgjohns.com)

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 81
  • Posts: 1340
  • He's just this guy. You know?
    • wgjohns.com
Re: Just does not want to work
« Reply #4 on: August 17, 2006, 01:17:24 AM »

Make sure House Code "D" is set as a "Tranceived House Code" in AHP Hardware Setup.
Logged
-Bill- (of wgjohns.com)
bill@wgjohns.com

In the real world, the only constant is change.

When I'm online you can find me in the Home Automation Chat Room!

robandcathy

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 6
Re: Just does not want to work
« Reply #5 on: August 17, 2006, 10:12:11 PM »

will the house code tras.. set to d affect the timers on the a code ; this is my setup A and B are all my switches c  is cameras and D is sensors what would be the best way to set up my usb transciver, i have timers to trigger lights for me in the morining on the a code
Logged

-Bill- (of wgjohns.com)

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 81
  • Posts: 1340
  • He's just this guy. You know?
    • wgjohns.com
Re: Just does not want to work
« Reply #6 on: August 17, 2006, 11:39:11 PM »

will the house code tras.. set to d affect the timers on the a code ; this is my setup A and B are all my switches c  is cameras and D is sensors what would be the best way to set up my usb transciver, i have timers to trigger lights for me in the morining on the a code
From my experience with AHP, I would suggest setting all of the houscodes to transceived unless this causes problems.  I think the macros will not be triggered if the house code of their trigger isn't set to be transceived.
Logged
-Bill- (of wgjohns.com)
bill@wgjohns.com

In the real world, the only constant is change.

When I'm online you can find me in the Home Automation Chat Room!
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.