🖥️ActiveHome Pro > Help & Troubleshooting

Re: ATTENTION: Good Batch of CM15A's!! [Manufd: 2005/03/15] [4 of 5]

(1/5) > >>

Tuicemen:
SteveRF check out <BR>http://forums.accessx10.com/showthread.php? <BR>s=&threadid=347 If you post there breifly <BR>your setup I'll recreate with iWitness <BR>running and let you know my results. I've <BR>managed to get what I think is your setup <BR>working.I'll repost results here In the <BR>iWitness forum.

ATTENTION: Good Batch of CM15A's!! [Manufd: 2005/03/15] [1 of 5]

Re: ATTENTION: Good Batch of CM15A's!! [Manufd: 2005/03/15] [2 of 5]

Re: ATTENTION: Good Batch of CM15A's!! [Manufd: 2005/03/15] [3 of 5]

Re: ATTENTION: Good Batch of CM15A's!! [Manufd: 2005/03/15] [5 of 5]


[TTA Edit: Experiment to determine whether or not SPLITTING 'Highly-Viewed' / 'Highly-Replied' but currently INACTIVE threads from LONG, LONG AGO (I'm starting with ~2 years) into parts will allow current ACTIVE threads to appear in the Top 10 Topics (by Replies) section of the Statistics Center (aka More Stats) Page.

NOTE: I *WILL* address the <BR> problem...]

david j. weiner:
Hello all,
Well, my stand-alone test of the CM15a
(attached to an "off" computer) is complete.
The simple timers seem to work acceptably
(within two minutes) past day four. There
was only one instance of a phantom signal
(as determined by an unprogrammed light on),
but that's probably my freezer or something
cycling. I have reconnected the CM15a to its
normal computer and downloaded the latest
version (3.186). So far there is a new
problem, but it may be temporary. Now the
GUI switch icons don't know the state of the
controlled objects. They show blue with a
question mark. The controllers are in the
correct state, the software just doesn't
know it. This is only true after
programmatic control, not remote. I have had
this happen before, the first time after a
program was upload to the controller. I'll
let it go for another 48 hours or so.
Anyhow, my CM15A's serial # is 04J41.
I'm running XP pro, SP2 up to date.
djw

SteveRF:
So far so good...
My setup with 3.186 is hanging in there with
timers and macros firing right on schedule.
Theonly error so far si the status report not
showing the correct flag status.  Everything
else seems to be exactly on time.
20 modules, 11 macros, 10 timers..
WinXP/Pro/SP2  Unit 04J44 4Mar
SteveRF

heil:
I clicked the link to the news story...
http://news.com.com/2100-1014_3-
5095260.html

and my porch light turned on.

One who is warching:
Heil:
Did you then follow the standard operating
procedure.  Do a Master reset... OOOPS no
master reset so you have to disconnect from
USB, unplug from wall, remove the batteries,
face due NNW and thump your chest 5 times
waiting for 5 seconds between thumps.  Now
reconnect to USB, plug back into wall,
reinstall AHP....

WAIT A MINUTE THIS IS STUPID IT IS TOTAL
BS!  Why do you people put up with this BS?

GET AN RMA, SEND IT BACK AND GET YOUR
REFUND.  THERE ARE WORKING RELIABLE PRODUCTS
OUT THERE!

YOU DESERVE BETTER!  :-}

Navigation

[0] Message Index

[#] Next page