X10 Community Forum
🔌General Home Automation => Automating Your House => Troubleshooting Automation Problems => Topic started by: Luigi524td on October 28, 2006, 02:55:28 PM
-
I'm a newcomer to X10 and would like to use one of the remotes to control my non rolling code Stanley Garage Door opener. I've been able to do that with the homelink trtansmitter in my car but can't seem to find the directions on these forums ???.
What I have read is there are range problems when there are steel doors etc but that doesn't concern to me.
:o
Any direction would be appreciated.
-
The KR19A are not learning remotes. They send a fixed set of preprogrammed codes that are recognized only by X10 compatible RF receiver. Garage door openers are generally will note recognize the signal from the KR19A.
Now if you want to use your KR19A as a garage door opener, you would have to take the long route.
you would pass the RF signal from the KR19A to a X10 receiver <-> which will then activate a contact closure module.
the contact closure module can be wired directly into your garage door opener just like your existing garage door wall
button. or you can open up an existing garage door opener remote and solder the contacts to the spot where the little
push button is connected.
You can use a powerflash module for the contact closure effect. I use a IP Power 9212 to control my garage door. Easier for me to set up security and the timer on the powerflash sometimes is to long and will cause my garage to stop midway.
The RF signal from the KR19A goes to my computer. Apply rules to filter out stray signal (a little more complex such as
On + Bright + On : before the signal is recognized). Then send an IP packet over to the 9212 to trigger the contact and open my garage.
Kr19A + RR501 or V572A (more sensitivity / range) + Powerflash = Classic X10 Garage Opener.
-
You can use a powerflash module for the contact closure effect. I use a IP Power 9212 to control my garage door. Easier for me to set up security and the timer on the powerflash sometimes is to long and will cause my garage to stop midway.
The RF signal from the KR19A goes to my computer. Apply rules to filter out stray signal (a little more complex such as
On + Bright + On : before the signal is recognized). Then send an IP packet over to the 9212 to trigger the contact and open my garage.
Kr19A + RR501 or V572A (more sensitivity / range) + Powerflash = Classic X10 Garage Opener.
You probably meant to write Universal Module rather than Powerflash.
For the OP: The UM closes its contacts when it receives a powerline signal. The Powerflash sends a powerline signal when its contacts are closed.
-
I have set up several Universal Modules for garage doors, they work very well for this application.
-
I have set up several Universal Modules for garage doors, they work very well for this application.
Stacking an appliance module (or two) between the UM506 and the wall adds a "combination code" to the mix. ;)
-
Excellent idea TTA. I added one in front of my 2 UM506. Now it has to be on for them to work. I use a SH624 palm pad and use the 4 bottom buttons, 2 for the UM506, one works the appliance module and the 4th does a light. The top half runs the alarm. I also have a macro that turns on and off the appliance module at set times of day.
One thing I noticed with the UM506's is that I have one that won't snap over when it gets cold. Bring it in and let it warm up and its OK. The other one doesn't seem to care about the cold... least not yet.
-
You probably meant to write Universal Module rather than Powerflash.
:-X Thanks for correcting (and in such a nice way too I must add).
Stacking an appliance module (or two) between the UM506 and the wall adds a "combination code" to the mix. ;)
8) Would be nice if they had a "Garage" module that did combination like this in one unit. It's a nice way to add extra security.
-
8) Would be nice if they had a "Garage" module that did combination like this in one unit. It's a nice way to add extra security.
Personally, I wouldn't want any entrance to my home having access capabilities available on the internet or become open because of power line noise. ;) :)
-
If someone hacks my router I'd be in big trouble. hehe.
Actually if someone finds my telephonen access key, i'd be in big trouble.
I have asterisk linked pretty tightly into every component in my home.
If someone sniffs my X10 security signal with one of the rxcom product I'd be
in big trouble.
If someone has a lockpick kit i'd be in big trouble (cut phone lines and gone in 60s =).
If someone chops of my finger and pushs it against my fingerprint lock .. euu.
---
That's when you take the extra step to impliment intrusion detection systems. ;D
Sip Calls if Phone line dies,
Backup Power if someone cuts power.
Phone -> internet shutdown incase of hack detection.
big red button on wall to disable everything..
Then you realize you have too much time on your hand.
-
;D Well there you have it. Your question answered successfully. ;D
I just wanted to add this little note.
With the UM506 (universal module) wired to your opener. Your original remote will still work.
So, don't go throwing it out.