X10 Community Forum

🛡Home Security => Problems and Troubleshooting => Topic started by: rlcot1 on May 23, 2007, 07:16:48 PM

Title: EagleEye-won't work unless on A1
Post by: rlcot1 on May 23, 2007, 07:16:48 PM
Hi
Need some help.  I followed directions to the tee and can't get my motion to wokr unless on A1.  I have two different rooms with my tranformer set on A and that room works fine.  When I set my second motion to A2 with my lampmodule set to A2 it won't work.  But when I set it back to A1 it works.  the problem with that is when I walk into one room the other room light comes on with the first one.  They also go off the same time.  I've tried other combo such as setting my home to b etc.  Nothing works except A1.  Thanks for your help
Title: Re: EagleEye-won't work unless on A1
Post by: -Bill- (of wgjohns.com) on May 23, 2007, 09:55:23 PM
Hi
Need some help.  I followed directions to the tee and can't get my motion to wokr unless on A1.  I have two different rooms with my tranformer set on A and that room works fine.  When I set my second motion to A2 with my lampmodule set to A2 it won't work.  But when I set it back to A1 it works.  the problem with that is when I walk into one room the other room light comes on with the first one.  They also go off the same time.  I've tried other combo such as setting my home to b etc.  Nothing works except A1.  Thanks for your help

Okay, first, when using motion detectors, each one takes up two "unit codes".  If the motion detector is programmed to A1, it will send A1 ON and A1 OFF as responses to motion.  It will send A2 ON and A2 OFF when the built-in light sensor decides it is light out or dark out.  So, you must skip a unit code between motion detectors.  The next valid address to set the second detector to would then be A3, and it would use A3 for motion and A4 for light / dark!

Second, try swapping the motion detectors, if neither one works in one location, then you may have an RF range problem.
Title: Re: EagleEye-won't work unless on A1
Post by: HA Dave on May 24, 2007, 12:40:14 AM

 I've tried other combo such as setting my home to b etc.  Nothing works except A1.  Thanks for your help


Another point.... the motion sensors don't hold program information when the batteries are removed. Since the batteries rest over the mounting screws, this means the sensors must be installed BEFORE the sensors are programed.

That can be awkward for some installations. Some of us (me included) have used Velcro to mount the sensor so we can program it ... then stick it where it's needed.
Title: Re: EagleEye-won't work unless on A1
Post by: -Bill- (of wgjohns.com) on May 24, 2007, 09:57:08 PM

 I've tried other combo such as setting my home to b etc.  Nothing works except A1.  Thanks for your help


Another point.... the motion sensors don't hold program information when the batteries are removed. Since the batteries rest over the mounting screws, this means the sensors must be installed BEFORE the sensors are programed.

That can be awkward for some installations. Some of us (me included) have used Velcro to mount the sensor so we can program it ... then stick it where it's needed.

Good point Dave!   ;D
Title: Re: EagleEye-won't work unless on A1
Post by: JimC on May 25, 2007, 06:12:07 AM
Quote from: Dave_x10_L
That can be awkward for some installations. Some of us (me included) have used Velcro to mount the sensor so we can program it ... then stick it where it's needed

Excellent point Dave. Nothing worse than trying to program a motion sensor while standing on a ladder in bright sun light. :)

Jim