X10 Community Forum

🔌General Home Automation => Automating Your House => Topic started by: tolum on November 12, 2007, 04:54:22 PM

Title: XPFM wiring for CFL
Post by: tolum on November 12, 2007, 04:54:22 PM
Hi; I have 9 CFL spots in my kids game room. The lights are controlled by a standard wall switch.
Question: Can I leave the actual wall switch and wire a XPFM in parallel so I will be able to control the lights with a Macro, a remote or a motion sensor or the actual wall switch?

Title: Re: XPFM wiring for CFL
Post by: Oldtimer on November 12, 2007, 06:48:42 PM
Hi; I have 9 CFL spots in my kids game room. The lights are controlled by a standard wall switch.
Question: Can I leave the actual wall switch and wire a XPFM in parallel so I will be able to control the lights with a Macro, a remote or a motion sensor or the actual wall switch?


Replace the switch with an XPS3 X10 switch.  It will give you both manual and remote control of the CFLs.
Title: Re: XPFM wiring for CFL
Post by: tolum on November 12, 2007, 07:10:48 PM
I think Xps3 switch need 3 wires from the electrical panel. I only have 2 wires!
Title: Re: XPFM wiring for CFL
Post by: Brian H on November 12, 2007, 08:02:23 PM
The XPFM Module usually mounts directly in the fixture though can be out into a switch box. It also needs a neutral power wire. I am not 100% sure if a manual switch from Line to Load on an XPFM would hurt it. I don't thing so but never tried it.
Title: Re: XPFM wiring for CFL
Post by: Oldtimer on November 12, 2007, 10:50:02 PM
I think Xps3 switch need 3 wires from the electrical panel. I only have 2 wires!

Even if you don't have a ground/bare (or green) wire in your box, as long as you do have a hot/black and a neutral/white return wire the XPS3 should work.
Title: Re: XPFM wiring for CFL
Post by: Oldtimer on November 12, 2007, 10:56:23 PM

 I am not 100% sure if a manual switch from Line to Load on an XPFM would hurt it. I don't thing so but never tried it.


I've put relay contacts in parallel with regular appliance modules with no problem.  That would be the same as putting a regular switch in parallel with an appliance module.  You have to be very careful that you get the polarity right when you do it or you'll get a short circuit.  I'm not sure though what the benefit would be of putting the switch in parallel with the X10 module since, when the switch was on, the module wouldn't be able to control the lights. Same goes with putting it in series since, when the switch was off, the module wouldn't be able to control the lights.
Title: Re: XPFM wiring for CFL
Post by: tolum on November 13, 2007, 07:19:02 AM
I think Xps3 switch need 3 wires from the electrical panel. I only have 2 wires!

Even if you don't have a ground/bare (or green) wire in your box, as long as you do have a hot/black and a neutral/white return wire the XPS3 should work.

Do you mean I can use a XPS3 switch and screw the green wire to the bottom of the steel wall switch electrical box where the bare ground is crewed too?

Title: Re: XPFM wiring for CFL
Post by: Oldtimer on November 13, 2007, 12:15:18 PM
I think Xps3 switch need 3 wires from the electrical panel. I only have 2 wires!

Even if you don't have a ground/bare (or green) wire in your box, as long as you do have a hot/black and a neutral/white return wire the XPS3 should work.

Do you mean I can use a XPS3 switch and screw the green wire to the bottom of the steel wall switch electrical box where the bare ground is crewed too?


Let me clarify all this some more.

First what we're discussing applies to both the XPS3 and the WS13A.  Neither of these appliance switches has any leads on it.  They have an 8 connection terminal strip.  Two to connect to the line/black.  Two to connect to the neutral/white.  Two to connect to your load/CFL light fixtures.  Two for 3-way control, which you're not using. There is no connection, nor is one needed, for ground/bare (or green).

Presumably you have a black and a white wire coming from your breaker box and and black and white wire going to your CFL fixtures.  Both white wires connect to the neutral terminals.  The black wire from the breaker connects to a line terminal.  The black wire to the CFL fixture connects to a load terminal.  Nothing will be connected to the control terminals.


Title: Re: XPFM wiring for CFL
Post by: tolum on November 13, 2007, 02:17:02 PM
I think Xps3 switch need 3 wires from the electrical panel. I only have 2 wires!

Even if you don't have a ground/bare (or green) wire in your box, as long as you do have a hot/black and a neutral/white return wire the XPS3 should work.

Do you mean I can use a XPS3 switch and screw the green wire to the bottom of the steel wall switch electrical box where the bare ground is crewed too?


Let me clarify all this some more.

First what we're discussing applies to both the XPS3 and the WS13A.  Neither of these appliance switches has any leads on it.  They have an 8 connection terminal strip.  Two to connect to the line/black.  Two to connect to the neutral/white.  Two to connect to your load/CFL light fixtures.  Two for 3-way control, which you're not using. There is no connection, nor is one needed, for ground/bare (or green).

Presumably you have a black and a white wire coming from your breaker box and and black and white wire going to your CFL fixtures.  Both white wires connect to the neutral terminals.  The black wire from the breaker connects to a line terminal.  The black wire to the CFL fixture connects to a load terminal.  Nothing will be connected to the control terminals.

Thanks a lot. This is clear as crystal!

Thierry

[Puck edit: moved reply outside of quote.]

Title: Re: XPFM wiring for CFL
Post by: tolum on November 13, 2007, 02:49:32 PM
Just asking, is it the same wiring process to wire a fan to a X10Pro XPDI3? I would like to control a small fan speed.
Title: Re: XPFM wiring for CFL
Post by: Oldtimer on November 13, 2007, 04:01:32 PM
Just asking, is it the same wiring process to wire a fan to a X10Pro XPDI3? I would like to control a small fan speed.

The XPDI3 has leads instead of a terminal strip but because it requires a neutral connection the wiring is similar to what I described for the XPS3 except you'll be using wire nuts instead of a terminal strip. 

A word of CAUTION though! The XPDI3 is not intended for inductive loads like a fan motor although many have reported that it will work as long as you don't exceed the power rating.  Hopefully others on the forum will chime in on this issue.
Title: Re: XPFM wiring for CFL
Post by: x10Steve on December 18, 2007, 01:40:22 PM
Quote
A word of CAUTION though! The XPDI3 is not intended for inductive loads like a fan motor although many have reported that it will work as long as you don't exceed the power rating.  Hopefully others on the forum will chime in on this issue.
Quote

You can use this switch for inductive loads as stated in the manual and on multiple web pages.

http://www.activehomepro.com/accessories/pro/xpdi3_iw_wa1_s.html

http://www.x10pro.com/pro/pdf/xpdi3.pdf

"Powerful and flexible X10 Pro Wall Switch is the ideal solution for controlling inductive loads, such as low voltage lighting circuits and ceiling fans."