Please login or register.

Login with username, password and session length

Author Topic: Power Status module  (Read 15191 times)

JeffVolp

  • Moderator
  • Hero Member
  • *
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Power Status module
« on: October 04, 2009, 11:22:29 AM »

I finished my first pass at a schematic, and started looking at the layout.  One issue is that only the largest "XTB-size" Polycase will accept an AC receptacle.  I had wanted to build a smaller module, but that may not be feasible.

One possibility is to custom-machine the blank cover to accept a polarized receptacle rather than the grounded receptacle.  I don't think that is the right approach because I can see this unit being used to monitor power consumed by a grounded device, such as a sump pump.  Does anyone have a problem with the module being 4" x 2.125" x 2.5"?

An alternative might be to use the XPPF case.  With a smart transformerless power supply, it may be possible to squeeze everything onto that size PCB.  That would make the module quite a bit smaller, but the color would be black.

Thoughts?

Jeff

Logged
X-10 automation since the BSR days

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: Power Status module
« Reply #1 on: October 04, 2009, 11:28:13 AM »

Black is fine,  I lived with Ivory only WS units from the shack for years.

I don't think that I'd lose the ground pin.

Smart power supply?  I hope it's smarter than the Cellet.
Logged
Remote control is cool,

but automation rules!

JeffVolp

  • Moderator
  • Hero Member
  • *
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Re: Power Status module
« Reply #2 on: October 04, 2009, 11:58:16 AM »

Smart power supply?

A transformerless power supply uses a capacitor to drop the line voltage to the voltage needed by the unit.  Whatever power is not used by the operating electronics is wasted a heat in a shunt regulator.  The TW523 actually takes advantage of that by having the LED on when the unit is not transmitting, so the energy normally consumed by the LED is available for the transmitter.

A "smart" transformerless supply would have two power levels.  The lower level would provide sufficient energy for the microcontroller.  The second level would provide additional power for the transmitter.  That energy would not normally be dumped into a shunt regulator.  The microcontroller would kick on the second stage when it is transmitting.

Jeff
Logged
X-10 automation since the BSR days

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: Power Status module
« Reply #3 on: September 29, 2010, 08:17:03 PM »

Jeff,

What's the status on this project?  I could probably use one or two of these.
Logged
Remote control is cool,

but automation rules!

JeffVolp

  • Moderator
  • Hero Member
  • *
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Re: Power Status module
« Reply #4 on: September 29, 2010, 08:46:36 PM »

What's the status on this project?  I could probably use one or two of these.

I completed the circuit design and started working on the prototype PCB.  Even simplifying the circuitry as much as possible, it is still almost as complex as the XTBR.  In small quantities, I thought it would be way too expensive for the target market, so I abandoned the project for now.

There are much less expensive "kluges" that can be used to monitor device currents.

Jeff
Logged
X-10 automation since the BSR days

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: Power Status module
« Reply #5 on: September 29, 2010, 09:00:08 PM »

Kludge may be cheaper, but seldom does it provide the satisfaction of completing a JVDE kit.  I'd love to plunk a couple of these into my environmental controls including the heater that i use to defrost the truck in the mornings.

Is $50 each a low end figure for the kit?  How about a plans/parts list and we fend for ourselves?  (do they still sell DIY etching kits?)

Obviously the PIC would have to come from JVDE.
Logged
Remote control is cool,

but automation rules!

JeffVolp

  • Moderator
  • Hero Member
  • *
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Re: Power Status module
« Reply #6 on: September 29, 2010, 09:24:28 PM »

Thank you for the compliment on my kits.

Right now the power monitor is on hold.  The firmware development never got past the concept stage, and nothing was coded.  Maybe in the future...

At the expected volume, the kit would have cost over $50.

Jeff
« Last Edit: September 29, 2010, 09:26:11 PM by JeffVolp »
Logged
X-10 automation since the BSR days
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.