Please login or register.

Login with username, password and session length

Author Topic: How to hook up a STROBE LIGHT to X-10 system?????  (Read 8653 times)

mary972

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
How to hook up a STROBE LIGHT to X-10 system?????
« on: September 21, 2006, 10:07:53 PM »

Does anyone know how to hook up a strobelight to X-10 system?  I saw these strobelights at this site 
       
 http://homesecuritystore.com/ezStore123/DTProductZoom.asp?productID=570

It has 2 wires and i'm wondering how to hook it up.  If you know how, please let me know.  Thanks..
Logged

KDR

  • Hero Member
  • *****
  • Helpful Post Rating: 53
  • Posts: 758
    • Home Automation Chat
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #1 on: September 22, 2006, 06:05:06 AM »

The easy way since they tell you voltage and current draw is to get a small plug-in DC power supply and plug that into a appliance module. There are several ways it could be done depending on your application. If you give us some details of what you have in mind I'm sure me and others will give you some other options.

Depending on the power supply used you may also need a filter in the circuit so it doesn't mess up your system.
Logged
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

mary972

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #2 on: September 22, 2006, 09:58:19 AM »

Hmmm i just want to hook it up to my Lamp Module so it will flash whenever my X-10 is triggered.  Where can i get that small Plug-In Power? 
Logged

Charles Sullivan

  • Hero Member
  • *****
  • Helpful Post Rating: 94
  • Posts: 1565
    • HEYU - X10 Automation for Linux, Unix, and Mac OSX
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #3 on: September 22, 2006, 11:32:36 AM »

Hmmm i just want to hook it up to my Lamp Module so it will flash whenever my X-10 is triggered.  Where can i get that small Plug-In Power? 

Radio Shack sells wall-wart power supplies that will work with this strobelight.  However you MUST use an Appliance Module - a Lamp Module isn't suitable for this application.

Logged
Yesterday it worked.
Today it doesn't work.
X10 on Windows is like that.

HEYU - X10 Automation for Linux, Unix, and Mac OS X     http://www.heyu.org

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #4 on: September 23, 2006, 07:41:56 AM »

I agree with Charles. A Lamp Module and a wall wart is not a good combination. Use a Appliance Module.
Guess a UM506 [costs more] Universal Module in series with the 12V would also work.
Logged

DowNet

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 40
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #5 on: September 23, 2006, 12:45:54 PM »

The easy way since they tell you voltage and current draw is to get a small plug-in DC power supply and plug that into a appliance module. There are several ways it could be done depending on your application. If you give us some details of what you have in mind I'm sure me and others will give you some other options.

Depending on the power supply used you may also need a filter in the circuit so it doesn't mess up your system.

Can you "switch" a "filtered" device?  Meaning if I have a power supply on a filter and also hooked up to a module, I don't think it will turn on and off, would it?  I thought the purpose of the filter was to filter out X10 PLC so it won't get to that particular device.  Please elaborate if I am incorrect. Thanks.
Logged

KDR

  • Hero Member
  • *****
  • Helpful Post Rating: 53
  • Posts: 758
    • Home Automation Chat
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #6 on: September 23, 2006, 01:26:56 PM »

The filter is to block noise. It will pass the PLC signal.

I just setup a test with a FilterLinc 1626-10    Plugged the filter into the outlet, plugged a lamp module into the filter and a lamp into the lamp module. Lamp turns on fine from AHP and remotes.

Also flipped things around, plugged the module into the power first then the filter into the module then the light into the filter. Again lamp turns on with AHP or remotes.

If the device being controlled is creating the noise you would want the control module plugged into the outlet first, then the filter plugged into the module and then the device into the filter. I don't have a known device making noise that I can test this on but it should work OK.
« Last Edit: September 23, 2006, 01:31:38 PM by KDR »
Logged
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

DowNet

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 40
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #7 on: September 27, 2006, 03:11:19 PM »

The filter is to block noise. It will pass the PLC signal.

I just setup a test with a FilterLinc 1626-10    Plugged the filter into the outlet, plugged a lamp module into the filter and a lamp into the lamp module. Lamp turns on fine from AHP and remotes.

Also flipped things around, plugged the module into the power first then the filter into the module then the light into the filter. Again lamp turns on with AHP or remotes.

If the device being controlled is creating the noise you would want the control module plugged into the outlet first, then the filter plugged into the module and then the device into the filter. I don't have a known device making noise that I can test this on but it should work OK.

Doesn't that filterlinc also to prevent absortion of some X10 PLC to components on your network (i.e. PC power supplies, AV recievers, etc)?  If that is the case, those components should never see a PLC if filtered.  Likewise, then, the filtered unit never gets to "eat" up a PLC; so the filter let's it continue on the AC power line.  Am I right in my thinking here?
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #8 on: September 27, 2006, 04:17:55 PM »

Did on my APC BX1000 UPS. The FilterLinc and other X10 Filters are tuned to not pass the signals in the 120 Khz range. So if the filtered device is making noise it will not get back on the powerline. If the device is absorbing the X10 signals. They don't pass through the filter and the device can't absorb them.
Logged

KDR

  • Hero Member
  • *****
  • Helpful Post Rating: 53
  • Posts: 758
    • Home Automation Chat
Re: How to hook up a STROBE LIGHT to X-10 system?????
« Reply #9 on: September 27, 2006, 08:48:01 PM »

So what your saying Brian is that my modules shouldn't work on the other side of the filter right? I have no problems turning on and off units downline from the filter.
Logged
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.