Please login or register.

Login with username, password and session length

Author Topic: How Not To Wire A Garage Door Opener.  (Read 3755 times)

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: How Not To Wire A Garage Door Opener.
« Reply #1 on: March 17, 2011, 04:12:56 PM »

Where's the problem?         :'

I'm only kidding...I see the problem, they should have plugged the extension cord into an outlet, not the light socket.  It makes you have go in, flip on the light, then go back to car to open the door.  rofl   rofl

I'm sorry, sometimes I just can not stop myself.
« Last Edit: March 17, 2011, 04:21:28 PM by dave w »
Logged
"This aftershave makes me look fat"

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: How Not To Wire A Garage Door Opener.
« Reply #2 on: March 17, 2011, 04:20:57 PM »

My friend had an even scarier find.

His back porch's lights kept dimming with the slightest loads.
He traced the wring and found it wired with 300 OHM Twinlead for a TV antenna.  ::)  :o
Logged

beelocks

  • Hero Member
  • *****
  • Helpful Post Rating: 9
  • Posts: 250
Re: How Not To Wire A Garage Door Opener.
« Reply #3 on: March 17, 2011, 07:25:44 PM »

It's always a 'friend' who does this kind of stuff...

A friend of mine (we'll call him Gary, for that is his name) was trying to work out why the electricity on the upper floor of his mother's (Doreen) house had suddenly and mysteriously quit working. The house was in London, England and had been the family home for close to 25 years at the time of the incident. Please remember that standard electricity in my part of the world is single phase 240 volts :)

The entire upper floor, 3 bedrooms, a bathroom and landing, plus the laundry annex (tacked onto the back of the house) with a washer, drier and several sockets on a workbench was connected to an unswitched fused spur in the cupboard under the stairs which in turn had been spurred off the light fixture (without bulb) in that same cupboard.

The problem came to light (no pun intended) when Gary's mother decided to put a light-bulb into the fixture in the cupboard under the stairs and switched the light off.

It turns out that Gary's late father (Tony) was no electrical genius - Although his makeshift set-up had been working faultlessly for at least 3 years following his death from unrelated causes.

Tony (had he been alive at the time) would have argued that the fused spur was a major safety feature. However his argument would have been completely pointless when it was discovered that the standard 13 amp fuse had been replaced with a piece of broken screwdriver.

Names and locations have NOT been changed to protect the innocent. Happy St Pat's Day, Tony - you were a fine Irishman  >!
Logged
Although my explanations may not be exactly clear, I do hope for slightly less cloudy.

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: How Not To Wire A Garage Door Opener.
« Reply #4 on: March 17, 2011, 08:23:14 PM »

Where's the problem? 
I'm only kidding...I see the problem, they should have plugged the extension cord into an outlet, not the light socket.  It makes you have go in, flip on the light, then go back to car to open the door. 

The solution would have been to duct tape the switch up (on). Then the laundry room light could have been turned on/off by unscrewing the bulb a half a turn for off.. and tighten it a half a turn for on. That is how I've always seen it done.

In my house I found a wall board electric heater that had been hardwired to a thermostat and an outlet... all hidden in the wall... using zipcord.
Logged
Home Automation is an always changing technology
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.