Contact | X10.com
Please login or register.

Login with username, password and session length

Author Topic: SR227 Problem  (Read 3438 times)

always1961

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
SR227 Problem
« on: January 21, 2015, 08:49:06 PM »
All of sudden my SR277 receptacles are hot top and bottom and I can't turn them on or off with the remote. 
Any ideas would be greatly appreciated.

Thanks for looking...
Logged

bkenobi

  • PI Expert
  • Hero Member
  • ******
  • Helpful Post Rating: 24
  • Posts: 2089
Re: SR227 Problem
« Reply #1 on: January 21, 2015, 10:55:36 PM »
Typically when things stop to function all of a sudden, it has to do with something changing on the home.  Things to look for include:

New computer equipment
New DC adapters (cell phone chargers)
New TV or other appliance that never fully turns off
Failing fluorescent ballast or CFL bulb

There could be other issues, but these are the most common.
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13307
Re: SR227 Problem
« Reply #2 on: January 22, 2015, 06:01:42 AM »
You may want to cycle the power to the SR227 Off for a minute and then power it back up.
If the control electronics where confused. A power cycle reset may help.

If it is much hotter than you remember.
Verify the load is not to large for the module to handle.
Much hotter than normal could also indicate a internal failure inside the SR227. Causing it to be too hot and not responding to commands.
In that case replacement is the best option.

Another indication of an electronics failure. Would be a odd burning smell of over heated electronic components.
« Last Edit: January 22, 2015, 06:05:20 AM by Brian H »
Logged

JeffVolp

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 122
  • Posts: 2301
    • XTB Home Page
Re: SR227 Problem
« Reply #3 on: January 22, 2015, 09:40:39 AM »
By hot top and bottom, I think the original poster means the power is there, not temperature.  My first guess would be that little plastic piece that ratchets the relay on and off has snapped.  That happened to one of mine years ago.

Jeff
Logged
X-10 automation since the BSR days

bkenobi

  • PI Expert
  • Hero Member
  • ******
  • Helpful Post Rating: 24
  • Posts: 2089
Re: SR227 Problem
« Reply #4 on: January 22, 2015, 11:34:01 AM »
Oh, one other thing.  I use these outside in "weatherproof" boxes.  One of these boxes wasn't so weatherproof at my old house and I found that moisture made it stop working.  I uninstalled that module and brought it inside to dry out then reinstalled with a better box.  It worked fine once more.  Obviously, this is a problem for more than just reliability!
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13307
Re: SR227 Problem
« Reply #5 on: January 22, 2015, 11:34:58 AM »
OH yes. If the outlet is always On. The plastic piece is frequently broken.
I would think. You may hear the ratchet switch clunk a few times as it tried to go On or Off.
Logged

always1961

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
Re: SR227 Problem
« Reply #6 on: January 22, 2015, 12:06:05 PM »
Thanks for all the advice..And yes by 'hot' I meant that both bottom and top outlets are on.
I will try all that you have recommended...
Logged

always1961

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 3
Re: SR227 Problem
« Reply #7 on: January 22, 2015, 12:56:46 PM »
Mystery solved...The battery in the remote was dead. Replaced it and everything is working fine.

Thanks again for all your suggestions.  :)%
Logged

bkenobi

  • PI Expert
  • Hero Member
  • ******
  • Helpful Post Rating: 24
  • Posts: 2089
Re: SR227 Problem
« Reply #8 on: January 22, 2015, 02:10:50 PM »
Been there.   B:(
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.