iwitness software

Started by nick41, November 20, 2006, 05:27:41 PM

Previous topic - Next topic

nick41

thanks everyone i finally got it up and running but now it has lines in it like it needs tracking can anyone tell me what to do please :'(

tjdavj

Are you using a wired, or a wireless connection?

Typically, if using a wireless connection, this is interference from another RF source. ie: wireless phone, or wireless network.

HTH

Tuicemen

nick41 :

As tjdavj   stated it could be noise! Do an Advanced Search for "RF noise"

It will bring up lots of possible sources as well as workarounds and or cures! ;) :D ;D

Also try moving you antennas so they're pointing directly at each !

It will take some playing arround (and lots of reading) but you'll get the interferance figured out! ;)

Also check the X10 Knowledge base under wireless cams as well as under video senders for additional info! ;)
Please Read Topic:
General Forum Etiquette
Before you post!

nick41

hey thanks a lot im goijng to try that ill let u know what happens ok thanks again

nick41

well guess what i have tried everything its still doing the same thing could it be cause i have soo many electronics in my apartment could be doing this >?????

tjdavj

You still haven't told us if you using a wired or wireless system! Kinda hard to offer answers when you don't provide us with relevant information!

Quotei have soo many electronics in my apartment could be doing this

Oh, so you live in an apartment.. Hope you are on good terms with your neighbors, as anyone of them could have the equipment that is causing the interference.

nick41


lightiv

Hi Nick,

I just installed my camera system and ran into to problems also.  I finally have all the drivers install and every shows as x10 in Device Manager.

But still no video!  What did you do to get yours going?

lightiv

Well I connected the video receiver to my T.V. and with the camera within inches of it I get a very poor quality picture and for get the camera that is on the other side of a wall and about 15 to 20 feet away.

??? ??? ???

lightiv

Ok, do not forget to try the different positions (A, B, C & D) on the video receive.  I had move it to C and that was very bad.  Position A is the best.

Much happier.  Now I can do some real adjusting. 

Any suggestion on improving reception?

KDR

Quote from: lightiv on November 21, 2006, 02:27:42 PM
Well I connected the video receiver to my T.V. and with the camera within inches of it I get a very poor quality picture and for get the camera that is on the other side of a wall and about 15 to 20 feet away.

??? ??? ???

Could you give us a little more info? What cam are you using and if wireless what receiver?

I posted about the same time you did.... glad you got a picture now. Happy tuning.
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

lightiv

Hi KDR,

I still can not get a picture on the computer.

I have:

XCam2 WideEye Color Camera (XX17A)
Audio/Video Receiver (Mono) VR31A
USB Video Adapter (VA11A)

Thanks.

lightiv

Ok, I noticed the frequency slider in iWitness and lowered to 1 fps and then 5 fps and now I can see a very poor quality picture on the computer.

lightiv

Well, I will be sending these back.  I can get an acceptable picture when the camera a receiver have line of sight to each other and the camera in with anything in the way is iffy at best.  The cost/benefit does not add up.  Thank goodness for the 30 day guarantee.

How well do the "Wired" cameras work?

KDR

One thing you need to watch for is cordless phones and wireless networks. They will add noise to your picture. If you have them you could try turning them off to see if that helps. I have 6 wired cams and one wireless. The location of the wireless is such that I don't have a problem with it. The other 6 cams are all working good. I went with wired cams because of the phone and network interference issues.
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

SMF spam blocked by CleanTalk