Please login or register.

Login with username, password and session length

Author Topic: ATTENTION Potential DS7000 Customers  (Read 26900 times)

Puck

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 171
  • Posts: 1799
ATTENTION Potential DS7000 Customers
« on: December 14, 2008, 06:51:49 PM »

With the introduction of the new softstart lamp modules, be aware of a less than 100% compatibility between them and the DS7000 Security System.

Before you purchase, please read this thread: Security Lights Dim Rather than Flash...

If you cannot get or do not have the original lamp modules without softstart, it is important that you know how they will react when used together.
Logged

Charles Sullivan

  • Hero Member
  • *****
  • Helpful Post Rating: 94
  • Posts: 1565
    • HEYU - X10 Automation for Linux, Unix, and Mac OSX
Re: ATTENTION Potential DS7000 Customers
« Reply #1 on: December 15, 2008, 02:09:22 AM »

With the introduction of the new softstart lamp modules, be aware of a less than 100% compatibility between them and the DS7000 Security System.

Before you purchase, please read this thread: Security Lights Dim Rather than Flash...

If you cannot get or do not have the original lamp modules without softstart, it is important that you know how they will react when used together.


Just another minor oversight by X-10's technical management when the lamp modules were redesigned. 

One workaround is to use an LM15A Socket Rocket in a few key lamps which never have to be dimmed.

Logged
Yesterday it worked.
Today it doesn't work.
X10 on Windows is like that.

HEYU - X10 Automation for Linux, Unix, and Mac OS X     http://www.heyu.org

peg-leg

  • Sr. Member
  • ****
  • Helpful Post Rating: 11
  • Posts: 111
Re: ATTENTION Potential DS7000 Customers
« Reply #2 on: July 12, 2010, 10:55:22 PM »

So my lights should flash on and off instantly rather than dim on and off slowly? 
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: ATTENTION Potential DS7000 Customers
« Reply #3 on: July 13, 2010, 06:11:07 AM »

The latest LM465s with Soft Start should flash fine, when the security console is triggered.
I tested some earlier soft start LM465s {Date Code 08A01}. They did ramp up and down and not flash.
A later revision firmware LM465 {Date Code 09J44} will flash with the consoles trigger.
So how they act with an alarm is depending on when it was manufactured.
Before Soft Start and later revision Soft Start lamp modules should flash On and Off.
Early Soft Start will ramp up and down and not flash correctly.

With a standard X10 On or Off. All soft start lamp modules should ramp up and down at about a two second rate.
The difference between early and later revision soft start modules, is how they handle the All Lights On, All Lights Off, All Units Off commands and a fast cycle of On Off commands.
« Last Edit: July 13, 2010, 07:15:18 AM by Brian H »
Logged

tom j

  • Hero Member
  • *****
  • Helpful Post Rating: 16
  • Posts: 1270
Re: ATTENTION Potential DS7000 Customers
« Reply #4 on: November 19, 2010, 11:22:33 PM »

The latest LM465s with Soft Start should flash fine, when the security console is triggered.
I tested some earlier soft start LM465s {Date Code 08A01}. They did ramp up and down and not flash.
A later revision firmware LM465 {Date Code 09J44} will flash with the consoles trigger.
So how they act with an alarm is depending on when it was manufactured.
Before Soft Start and later revision Soft Start lamp modules should flash On and Off.
Early Soft Start will ramp up and down and not flash correctly.

With a standard X10 On or Off. All soft start lamp modules should ramp up and down at about a two second rate.
The difference between early and later revision soft start modules, is how they handle the All Lights On, All Lights Off, All Units Off commands and a fast cycle of On Off commands.


Hello Brian so could you assume that if you buy one now it will be the newer version?

Tom j.
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: ATTENTION Potential DS7000 Customers
« Reply #5 on: November 20, 2010, 06:13:11 AM »

Yes by now all of them should be Soft Start and the later revision. Purchased from X10. 09J44 would be week 44 of 2009.

I would think that most independent X10 authorized dealers would also have them by now.
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.