Please login or register.

Login with username, password and session length

Author Topic: PR511 Flood Light, Not a Light???  (Read 13142 times)

X10 Ken

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 30
PR511 Flood Light, Not a Light???
« on: February 13, 2009, 04:57:48 PM »

When I use "Turn on all lights" in room "Outside", no on commands are sent for my PR511 Flood Lights.

When "Outside" "All units off" is used, an off command is sent to the PR511.

So the question is: When is a light not a light?

The answer seems to be: When the light is a PR511.

This seems like a AHP bug to me.  Is it, or have I missed something?

Ken
===
Logged

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: PR511 Flood Light, Not a Light???
« Reply #1 on: February 13, 2009, 05:11:19 PM »

It's not an AHP bug.   The commands in the Rooms are "Turn All Lights on in ROOM name" and " Turn All UNITS off in ROOM name".   A PRS11 is a devise, not a Light.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: PR511 Flood Light, Not a Light???
« Reply #2 on: February 13, 2009, 05:30:09 PM »

My floodlight does react to the "All Lights On" command... I know that only because one of the floods are on the same House code as the alarm.

I am not sure what your problem is X10 Ken do you have a PR511 in the "outside room"... you could try replacing it with a dummy lamp module with the PR511's unit code.
« Last Edit: February 13, 2009, 05:32:27 PM by Dave_x10_L »
Logged
Home Automation is an always changing technology

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 282
  • Posts: 10497
  • I don't work for X10, I use it successfuly!
Re: PR511 Flood Light, Not a Light???
« Reply #3 on: February 13, 2009, 05:45:16 PM »

X10 Ken 
Not sure which version of AHP your running!
Version 3.236 works how you discribed. Is it a bug?
Well I'd say so! Using a thirdparty program and issuing an all lights on turned it on!  ::)
So if it was classed  a "Device" as Dan States not a "Light"  then it shouldn't have turned on for  Dave or me! ::) :'
 
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: PR511 Flood Light, Not a Light???
« Reply #4 on: February 13, 2009, 06:24:13 PM »

Rooms in AHP should not be confused with House Codes.  An ALL LIGHTS ON issued by an x10 controller will trigger all lights on that house code.  Sometimes users of AHP will have different light modules in different rooms on the same house code.  To prevent these from triggering, AHP will turn on the lights in a room one at a time and not issue the ALL LIGHTS ON command over the powerlines.  I believe that the ALL LIGHTS ON command can be used in macros and the like under the advanced functions tab.
I'm also guessing that some of the SDK programs put the A-L-O command on the powerline.
Long story short, the Turn on all lights in a specific room is not the same as an A-L-O command.

Clear as mud, right?
Logged
Remote control is cool,

but automation rules!

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: PR511 Flood Light, Not a Light???
« Reply #5 on: February 13, 2009, 07:29:15 PM »

I ran a test (AHP 3.228, BTW) for my Outside room (PRS511 and a Lamppost).  When Turn all Units off, both the PRS551 and the Lamppost turned off, but when Turn all Lamps on was clicked, only the Lamppost turned on.  My PRS511 is defined as a Device, not as a lamp in AHP.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

X10 Ken

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 30
Re: PR511 Flood Light, Not a Light???
« Reply #6 on: February 13, 2009, 08:16:51 PM »

My PRS511 is defined as a Device, not as a lamp in AHP.

Yes AHP is defining it as a Device, not a lamp.  However, "All Lights On" on a hard wired controller set to house code K does turn on the flood light.  This means that the flood responds to "K All Lights On" and the flood thinks of itself as a light.

In that:
1.  It is a light.
2.  It responds "All Lights On"
3.  AHP does not consider it a light.

This situation must be defined as a bug in AHP.

Anyone disagree?

Ken
===
Logged

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: PR511 Flood Light, Not a Light???
« Reply #7 on: February 13, 2009, 08:20:48 PM »

I'd consider it a programming oversight. 
Logged
Remote control is cool,

but automation rules!

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: PR511 Flood Light, Not a Light???
« Reply #8 on: February 13, 2009, 08:55:52 PM »


This situation must be defined as a bug in AHP.


OK.... AHP has another bug.
Logged
Home Automation is an always changing technology

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: PR511 Flood Light, Not a Light???
« Reply #9 on: February 13, 2009, 11:13:39 PM »


This situation must be defined as a bug in AHP.


OK.... AHP has another bug.


That "bug" has been part of AHP since the first release.  Every version I've had has it.   
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.