Contact | X10.com
Please login or register.

Login with username, password and session length
Pages: 1 [2]

Author Topic: AHP and 3-pin AppModule problem  (Read 9509 times)

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: AHP and 3-pin AppModule problem
« Reply #15 on: July 30, 2009, 10:57:22 PM »
No.

It (the PSC01) is a Powerflash Security Interface, not a phase coupler. If you have an electric dryer, X10 makes a coupler that plugs into the dryer outlet.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

birdzeye

  • Hero Member
  • *****
  • Helpful Post Rating: 3
  • Posts: 475
Re: AHP and 3-pin AppModule problem
« Reply #16 on: July 31, 2009, 08:13:37 AM »
Quote from: Dan Lawrence on July 30, 2009, 10:57:22 PM
No.

If you have an electric dryer, X10 makes a coupler that plugs into the dryer outlet.

What's it called?
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: AHP and 3-pin AppModule problem
« Reply #17 on: July 31, 2009, 11:49:23 AM »
Quote from: birdzeye on July 31, 2009, 08:13:37 AM
Quote from: Dan Lawrence on July 30, 2009, 10:57:22 PM
No.

If you have an electric dryer, X10 makes a coupler that plugs into the dryer outlet.

What's it called?
It's not from X10, it is from Smarthome.com

This is the repeater, the coupler is a little cheaper, but it does not amplify.
http://www.smarthome.com/4826B/SignaLinc-3-Pin-Plug-in-Coupler-Repeater/p.aspx
Logged
"This aftershave makes me look fat"

birdzeye

  • Hero Member
  • *****
  • Helpful Post Rating: 3
  • Posts: 475
Re: AHP and 3-pin AppModule problem
« Reply #18 on: July 31, 2009, 03:29:55 PM »
I solved the problem by digging out an old TM751 and plugging the stereo into it, and changed the housecode to a new one separate from any of my other stuff. The stereo is snapping on and off from AHP now, and I can time it to come on and off by itself.

Quote from: dave w on July 31, 2009, 11:49:23 AM
It's not from X10, it is from Smarthome.com

This is the repeater, the coupler is a little cheaper, but it does not amplify.
http://www.smarthome.com/4826B/SignaLinc-3-Pin-Plug-in-Coupler-Repeater/p.aspx

Thanks for the link. I have a 4-pin dryer plug and may buy the corresponding coupler for it. I always thought this had to be done by an electrician at the main fuse box; didn't know it could be so simple as a plug!
Logged

stoney

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 42
Re: AHP and 3-pin AppModule problem
« Reply #19 on: September 06, 2009, 03:28:21 PM »
I was experiencing poor signal reach so I purchased an XPCR X10 PRO Signal Amplifier Coupler Repeater.

I shut off the Main Breaker in my Electrical Panel.

Connected the colored leads per the simple instructions (Red, Black, White) to an appropriate breaker.

Buttoned everything back up and turned Main back on.

Checked the system and wow! Signals wall to wall from upstairs to basement and out to garages.

It was on Ebay for slightly over $10 USD!!

Logged

evadorev

  • Sr. Member
  • ****
  • Helpful Post Rating: 4
  • Posts: 79
Re: AHP and 3-pin AppModule problem
« Reply #20 on: September 07, 2009, 08:33:34 PM »
try the cap on your clothes dryer plug instead or between the red and black wires of your kitchen counter plugs if it`s wired this way.

 
Logged
Mary had a little lamp, little lamp, controlled by X10 !!!! (kid song!!)
Pages: 1 [2]
« previous next »
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.