Contact | X10.com
Please login or register.

Login with username, password and session length

Author Topic: AM14A Schematic  (Read 4615 times)

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
AM14A Schematic
« on: August 25, 2010, 06:27:26 PM »
Gang,

I have old 2-way appliance module that is dead.  Unfortunately it ain't as simple as "that tube isn't lit".   (You youngins will have to ask an old geezer what that means.)

I would like to fix it as I have one of those "must know status" applications. Has anyone seen schematics for the AM14A?
« Last Edit: August 25, 2010, 06:33:52 PM by dave w »
Logged
"This aftershave makes me look fat"

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: AM14A Schematic
« Reply #1 on: August 25, 2010, 06:48:30 PM »
I have not seen one but will poke around.

How about. Why is that final tube glowing cherry red and the envelope is sucking in?  ;)
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: AM14A Schematic
« Reply #2 on: August 25, 2010, 07:45:09 PM »
Quote from: Brian H on August 25, 2010, 06:48:30 PM
I have not seen one but will poke around.

How about. Why is that final tube glowing cherry red and the envelope is sucking in?  ;)

Gee, I thought that is the way finals on a Motrac was supposed to run.  rofl
Logged
"This aftershave makes me look fat"

bitman

  • Hero Member
  • *****
  • Helpful Post Rating: 9
  • Posts: 597
Re: AM14A Schematic
« Reply #3 on: August 26, 2010, 09:09:33 AM »
I have seen more than one x10 device eat the small signal diodes. You can buzz em out in circuit. They should only conduct one way and they re the 1n914 / 1n4148 variety.
Logged
Long live X10! - Because I just like it is all.....

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: AM14A Schematic
« Reply #4 on: August 26, 2010, 09:28:46 AM »
Quote from: bitman on August 26, 2010, 09:09:33 AM
I have seen more than one x10 device eat the small signal diodes. You can buzz em out in circuit. They should only conduct one way and they re the 1n914 / 1n4148 variety.
Thanks Bits, I will check forward and reverse on all the diodes...maybe will get lucky. My luck will be a bad zener and I won't know breakdown voltage.

It's times like these I wish I had an O'scope.
Logged
"This aftershave makes me look fat"

JeffVolp

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Re: AM14A Schematic
« Reply #5 on: August 26, 2010, 09:51:42 AM »

I have one I could lend you if you need to do some A-B comparisons.

Jeff
Logged
X-10 automation since the BSR days

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: AM14A Schematic
« Reply #6 on: August 26, 2010, 12:40:05 PM »
I still have two in storage. I can do voltage measurement if you want them.
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: AM14A Schematic
« Reply #7 on: August 26, 2010, 01:28:19 PM »
Thanks Brian and Jeff!!

Let me actually do some "blind" troubleshooting first. I really have not done any "probing" at all. Might end up being something easy/obvious.

I will let you know.
Logged
"This aftershave makes me look fat"

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: AM14A Schematic
« Reply #8 on: August 26, 2010, 01:34:46 PM »
Well when my RR501 got flaky. I found the PC Board around the Zener Diode was dark and the solder had gotten flaky.
Same for the low value resistor in series with the cap to the line connection.
I replaced the zener with two hand picked in series for a better wattage rating and the main filter cap with a larger value.
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.