Please login or register.

Login with username, password and session length

Author Topic: Cm19A Linux Arm [Mochad]  (Read 9038 times)

luis84

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 21
Cm19A Linux Arm [Mochad]
« on: July 21, 2012, 03:23:51 PM »

Hello everyone,

I run a cm19a to capture input from a motion sensorwith mochad.  It works fine on my linux mint 13 system on my x86 netbook.

The issue however, is my Arm (Tegra 2) device.  It runs a 2.6.x.x kernel. I have xfce running on it and its stable, I installed mochad and netcat no problem.  When I plugin the cm19a it gets detected fine:

Code: [Select]
n  1 00:01:15 adam kernel: [   55.524391] Firmware version = wl0: Sep  7 2010 10:38:12 version 4.218.248.5
Jul 21 19:04:32 adam kernel: [  125.468910] usb 1-1.1: USB disconnect, address 3
Jul 21 19:04:43 adam kernel: [  136.459000] usb 1-1.2: new low speed USB device using tegra-ehci and address 5
Jul 21 19:04:43 adam kernel: [  136.495442] usb 1-1.2: New USB device found, idVendor=0bc7, idProduct=0002
Jul 21 19:04:43 adam kernel: [  136.495499] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Jul 21 19:04:43 adam kernel: [  136.495553] usb 1-1.2: Product: USB Transceiver
Jul 21 19:04:43 adam kernel: [  136.495588] usb 1-1.2: Manufacturer: X10 Wireless Technology Inc
Jul 21 19:04:43 adam mochad[1598]: starting
Jul 21 19:04:43 adam mochad[1599]: Found CM19A
Jul 21 19:04:43 adam mochad[1599]: In endpoint 0x81, Out endpoint 0x02

So it seems okay.  I can then nc localhost 1099 and it waits like my other device, normally commands would be output but with the tegra/arm device it just sits at netcat and never shows any commands the motion sensor sends.  If I plug the cm19a back into my netbook x86 it captures the commands from motion sensor fine.

Any ideas what it could be or what I could try to troubleshoot? There are no other errors in the messages log....

Thanks
Logged

bbx10node

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 7
Re: Cm19A Linux Arm [Mochad]
« Reply #1 on: July 21, 2012, 09:34:54 PM »

Try netcat from your mint system to the arm system. Some Linux systems ship with netcat(nc) that does not work!

http://archlinuxarm.org/forum/viewtopic.php?f=9&t=1499

By the way, what is the name of the Tegra 2 device? I am looking for something with more horsepower than my WiFi router for mochad and home automation.
Logged

luis84

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 21
Re: Cm19A Linux Arm [Mochad]
« Reply #2 on: July 22, 2012, 06:22:38 PM »

Thank you - may try that!  The device is a notion ink adam tablet.

However, if you want a device for home control that is compact and fully functional go with a trimslice.  They are amazing.
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.