Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[dave w]

OK...today I tried everything mentioned here!

So what happened when you plugged the TM751 in the outlet the CM15A was in?

[Noam]

When I tried to download new settings in my CM15A, I keep getting this error message..."Down load error" there's not enough space in the interface to download your timers & macros???

It sounds like you might have a corrupt AHX file.
Try this:
Unplug the CM15A (USB and power)
Remove the batteries
reboot the PC
Wait at least 5 minutes after having removed the CM15A's batteries, then put them back in.
Plug the CM15A back in (power and USB)

Clear the interface memory
Start a new AHX file, with one or two simple timers and/or macros (for testing - no point spending time re-creating it all yet).
Try downloading to the CM15A.

Let us know if that helps.

[bvrwally]

Dave, I was able to control the cameras with the TM 751 but not the CM15A, when I plugged them in the same outlet? The PC showed they were switching, but the CM15A was not in control of them? I've tried clearing the interface a number of times, and no luck so far? I left my computer on with the downloading in progress and when I returned a week later....it was still "Downloading"!!??

[dave w]

Dave, I was able to control the cameras with the TM 751 but not the CM15A,

OK that pretty much indicates it isn't a noise or coupling problem which is the direction I was going in..

Maybe CM15A is bad. I think Noam is going down that road. With the talk of X10 being in receivership, maybe now is the time to get a spare or two. 

[Tuicemen]

I left my computer on with the downloading in progress and when I returned a week later....it was still "Downloading"!!??

This indicates the CM15 memory is corrupt.
I've had a old one do this and it is fixable.
you'll need to:
purge delayed macros
clear the interface
empty deleted modules
unplug the cm15 from usb and outlet
remove batteries
wait 5 mins
Plug the Cm15a in and repeat above
then try uploading to the interface (download timers and macros),if it still fails redo the procedure.
once the download is successfull reinstall the batteries.

Note: it took acouple of time before mine started to accept info.
 

[dave w]

Note: it took a couple of time before mine started to accept info.
 

That's because you forgot to hold the CM15A above your head and do the dance.

[bvrwally]

Where is a good source for obtaining another CM15A without having to purchase additional software???

[Tuicemen]

Where is a good source for obtaining another CM15A without having to purchase additional software???

You could try X10 customer service and there is always e-bay

[dave w]

Where is a good source for obtaining another CM15A without having to purchase additional software???

CM15A with AHP is only $49 on X10.com, I think the eBay resellers are asking more right now. X10 customer service may have a "scratch and dent" like Tuicemen suggests.

[Tuicemen]

I picked up a VA12A by going into chat on the Vanguard selling page and requesting one without the software.
I'm sure the same could be done for the CM15A from a AHP perchase page.
 

[bvrwally]

I purchased another CM15A and will try to see if that clears up my problem? I just won't be able to install  it for another week, when I get back to my Beach Home! l Thanks for all of your help!

[bvrwally]

Here is a screen shot of what I found this weekend, after deleting all AHP and re-installing it along with a new CM15A! I have NEVER seen my limitation or selection of channels displayed as such??   

My "Ultimate" goal....is to monitor my garage/studio/apartment remotely. I have 4 cameras, security system, and just about every AHP add-on possible! I personally have come to the conclusion, yes, I have a noise issue. I have the coupler (XPCR) for my service panel, that was of no help. Changed interfaces, (CM15A). Deleted all references to AHP and re-installed it, along with my registration numbers. A TM751 does switch the cameras, when I am there, but I really need the CM15A to do so with my "Remote" software! Again, thanks for all of your help to date!
B.W.

[bvrwally]

Bump!