Contact | X10.com
Please login or register.

Login with username, password and session length

Author Topic: Pan and Tilt buttons no longer work but Sweep and Presets do  (Read 9277 times)

davideinmd

  • Sr. Member
  • ****
  • Helpful Post Rating: 3
  • Posts: 82
Pan and Tilt buttons no longer work but Sweep and Presets do
« on: November 29, 2011, 03:53:05 PM »
Since the last update to 3.318 I find that only camera C1 is fully functional from the AHP interface. I have two other Ninja setups and the only way I can get them to pan and tilt is by using a remote. They will, however, respond to commands from the AHP interface for sweep, center, and presets. Watching the activity monitor when I pan and tilt says it is transmitting 'C PanUp' but when I use it on the other cameras it says it is transmitting 'C PTZ Tilt #' (where # is a different number each time I hit a pan or tilt button on AHP.
Any ideas?
Logged

Noam

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 51
  • Posts: 2817
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #1 on: November 29, 2011, 03:56:48 PM »
What version of AHP were you using before?
What are the addresses of the other cameras?
What happens if you swap addresses (try another house code), does it send the correct commands? (no need to change the codes on the cameras, only in AHP - to test what commands are being sent - by checking in the Activity Monitor)

Do you have a CM15A, or a CM19A?

It is also possible that your AHX file is corrupted.
Logged

davideinmd

  • Sr. Member
  • ****
  • Helpful Post Rating: 3
  • Posts: 82
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #2 on: November 29, 2011, 04:05:50 PM »
I have been keeping up with updates regularly. C1, C2, C3 (not a ninja), C4. I have a CM15A.
Logged

Noam

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 51
  • Posts: 2817
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #3 on: November 29, 2011, 04:15:14 PM »
I don't have any cameras, so I can't test for you.
I haven't seen any other reports of problems with cameras not responding in AHP 3.318.

You can try changing the codes to D1-4 (just in AHP), and see what the Activity Monitor shows when you try to command the cameras.


You can also try creating a new AHX file, just with those cameras (on C1-4), just to see what the activity monitor shows (and see if the cameras respond).
Logged

davideinmd

  • Sr. Member
  • ****
  • Helpful Post Rating: 3
  • Posts: 82
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #4 on: November 29, 2011, 04:17:56 PM »
I'll try that. Thanks!
Logged

davideinmd

  • Sr. Member
  • ****
  • Helpful Post Rating: 3
  • Posts: 82
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #5 on: November 29, 2011, 04:48:07 PM »
After much brute force (I guess) I got it working. Don't know what happened there. Weird. But a lot of stuff been weird since the last couple of updates. Thanks again.
Logged

Noam

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 51
  • Posts: 2817
Re: Pan and Tilt buttons no longer work but Sweep and Presets do
« Reply #6 on: November 29, 2011, 05:50:01 PM »
You can always check the AHP Bug List (user-maintained) if you are unsure if something you are seeing was reported or not.
You can access the Bug List here:
http://forums.x10.com/index.php?topic=22373.0
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.