Please login or register.

Login with username, password and session length
Pages: [1] 2

Author Topic: Airsight Remote Viewing Guide (with pictures)  (Read 18929 times)

Tyler E

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 31
Airsight Remote Viewing Guide (with pictures)
« on: May 14, 2013, 01:20:28 PM »

How do I View my Camera Over the Internet?
A guide for setting up your Airsight camera before port forwarding

This step by step guide should be able to guide anyone through the procedures for getting your cameras set up so you can port forward them in the least painless way possible.

The X10 Wiki contains all of this information. However, the wiki doesn't really give you a lot of guidance for which ports or IPs you should use. My hope is that this will be a more readable format. I have suggested best practices to make sure your setup is not only working but working reliably for a long period of time.

This guide will include information for setting this up on a PC. I may do a Mac version at a later date.




Step One: Gather Information
We should begin by collecting all of the information we need. We will need:
  • Default Gateway (your router's IP)
  • IPv4 Address (your computer's IP)
  • Your router's make and model number
  • The login information for your router
Go look at your router and make a note of the make and the model number. You'll need this later. If there is a username and password on your router, note this as well.

Now we will find your IP information. There are a few ways to do this. By far the easiest way is to hit CTRL + R on your keyboard. This will open the Run Dialog. Type in cmd and hit enter; this will open the command prompt.



If you can't do that for some reason you can find the command prompt by going to Start -> All Programs -> Accessories -> Command Prompt.



Once you have the command prompt open type in ipconfig and hit enter. You should then have a screen in front of you that shows you a whole bunch of stuff. The only things we need to concern ourselves with at this point are the default gateway and IPv4 address. These should be right next to each other. If your default gateway has any letters or colons in it you need to keep looking. Write this information down, you'll need it in the next step.








Step Two: Static IP
Now we need to assign a static IP address to the camera. Log in to your camera through the web browser software. It doesn't matter what browser or mode you log in to at this point. I advise just logging in to it through the IP camera tool.

Here the instructions start to vary because of the different user interfaces between the MJPEG and H.264 cameras. I have split the guide into two sections at this point, starting with the MJPEG cameras.

MJPEG Static IP Guide (XX40A, XX36/42A, XX34/41A)
Once you get to the live video screen go to Network and then Basic Network Settings.





Once at this page it will just show Obtain IP from DHCP Server (1) and Http Port (6). Uncheck the box that says Obtain IP from DHCP Server and it will show the rest of the options I have in my screenshot here. Set them as follows:

1. Uncheck

2. This is the IP address of the camera. The first three sets of numbers will always match your default gateway. The last set of numbers, after the third period, should be a number that is between 2 and 254. I recommend using a number that is about 25 higher than your IPv4 address (remember, this is your computer's IP). For example, if my IPv4 address was 192.168.1.7, I would choose 192.168.1.41 for my camera's IP.

If you have more than one camera they all need their own IP addresses. I always advise

3. The subnet mask will always be 255.255.255.0.

4/5. These will both be your default gateway we found earlier.

6. By default this will be set to 80. We do not want to use port 80, instead, use something like 8001 or 8081. When using multiple cameras I advise using 8001, 8002, etc, because it is easier to remember.

Hit submit and your camera will reboot. Now we can move on to the next step.

H.264 Static IP Guide (XX39A/XX59A)
This is basically the same as for the MJPEG cameras, but with a few more options and one major change. From the live video screen, go to the params menu in the upper right corner.



From this next menu go to Basic Network Settings. You should see the following screen:



Once you are on this page set the Network Type to Static Address and it will show the rest of the options I have in my screenshot here. Set them as follows:

1. Set this to Static Address

2. Leave this as 38401 unless you have more than one camera. If you do, set them to 38401, 38402, etc.

3. By default this will be set to 80. We do not want to use port 80, instead, use something like 8001 or 8081. When using multiple cameras I advise using 8001, 8002, etc, because it is easier to remember.

4. Leave these alone.

5. This is the IP address of the camera. The first three sets of numbers will always match your default gateway. The last set of numbers, after the third period, should be a number that is between 2 and 254. I recommend using a number that is about 25 higher than your IPv4 address (remember, this is your computer's IP). For example, if my IPv4 address was 192.168.1.7, I would choose 192.168.1.41 for my camera's IP.

6. This stuff should all be set correctly. If your default gateway is not 192.168.1.1 you will need to change the Gateway and DNS Server here to match the correct default gateway for your network.

Hit update and your camera will reboot. Now we can move on to the next step.




Step Three: Port Forwarding
Honestly there are so many routers I can't even begin to make a comprehensive port forwarding guide. Your best resource at this point is going to be Port Forward, they have guides for just about every router under the sun.

I can offer some tips and help for avoiding common pitfalls though.

  • You must create a separate port forwarding rule for each camera; you cannot create a port range and open, say, 8001-8004. This is because each port is assigned to be opened for a specific IP address.
  • Whenever it asks for an IP address, it means the IP we assigned to the camera in step 2. It will only be the IP address, not the port or http:// or anything.
  • Internal, External, Start, and End ports will always be the ports assigned to the camera.
  • Protocol will always be TCP only. Not UDP, not TCP/UDP, just TCP.
  • For H.264 cameras you will need to forward the Media Port as well. By default this port is 38401, don't change it unless you have more than one camera.
If you have any trouble with this step you can post your problem here and we'll figure it out.




Step Four: Accessing Your Camera
In theory your camera should now be set up correctly and accessible over the internet, but how? There are two ways to do it, I'll go over both.

The way you should try first is by using the external IP address. This is different from any of the internal IP addresses that we found earlier. Basically the external IP is the address that other computers on the internet see your computer as. To find this address, go to google and enter "What is my IP", then hit enter.



If you did it right it should show you the IP right there. Make a note of it. On a device that is not connected to your network, such as a 3G/4G phone or tablet, enter this address followed by a colon then the port number of your camera. So for example, if my external is 63.211.211.114 and my port is 8001, I would enter 63.211.211.114:8001. This should pull up the login page for the camera.

There is drawback to this however. Your external IP address will change. That's okay! Don't pay for a static IP address from your ISP, you don't need it. Airsight cameras all have their own web address, called a DDNS Address. DDNS stands for dynamic domain name server, but that isn't really important for our purposes. This address will be on a sticker on the bottom of your camera, but we can also find it through the software. The procedure is basically the same for MJPEG and H.264 cameras.

Log in to your MJPEG camera and then go to System, then Device Info. The DDNS Status will be listed there. The web address will be something like http://a0000.airsight.net:8000. If it isn't listed there, go to Network, then DDNS Service Settings. The DDNS will be listed here under Manufacturer's DDNS. You will need to add a colon then the port number at the end.

For H.264 cameras, the only real difference is that you need to go the Parameters Screen instead of System. Note that neither the DDNS nor the external IP will work from inside your home network. You'll still have to use the internal IP when you're at home.




You're done!
If it doesn't work at this point, go back and double check your static IPs and port forwarding rules. Make sure you aren't connected to your wifi network on the device you're accessing it from. If you aren't sure, ask a friend to try it from their house. If you still can't get it, post your problem here and we'll take a look.

I don't think I missed anything, but if I did, or anything is confusing, point it out and I'll add/fix/explain it better.

If you made it this far and it works, congratulations. You did it. You're done. That's all I have. Good work.
#:)
« Last Edit: May 20, 2013, 04:47:29 PM by Tyler E »
Logged
Having trouble port forwarding your Airsight camera? Check out my guide!

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #1 on: May 14, 2013, 04:15:04 PM »

Very nice write up which I'm sure will help some.
A Plus one from me. ;)
 #:)
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #2 on: May 14, 2013, 05:34:52 PM »

Very nice write up which I'm sure will help some.
A Plus one from me. ;)
 #:)
Yes. It is too bad a user had to do it.
Logged
"This aftershave makes me look fat"

Tyler E

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 31
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #3 on: May 14, 2013, 05:51:43 PM »

Very nice write up which I'm sure will help some.
A Plus one from me. ;)
 #:)
Yes. It is too bad a user had to do it.
Well, I mean, I do work at X10. :)
Logged
Having trouble port forwarding your Airsight camera? Check out my guide!

richy2

  • Hero Member
  • *****
  • Helpful Post Rating: 6
  • Posts: 303
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #4 on: May 14, 2013, 09:25:29 PM »

Your secret is out Clark!
or

Are you really Tony Stark?

 B:(footnote:

everyone going email you for help

 #:)  :)+
« Last Edit: May 15, 2013, 03:59:46 PM by richy2 »
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #5 on: May 15, 2013, 09:55:10 AM »

Well, I mean, I do work at X10. :)
Excellent!! Where and why have you been hiding?
Logged
"This aftershave makes me look fat"

Tyler E

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 31
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #6 on: May 15, 2013, 11:02:45 AM »

Well I post when I have time, but I'm usually too busy. When I do post I try to make it something useful, like this.

EDIT: I also changed my forum handle because richy2 made me laugh.
Logged
Having trouble port forwarding your Airsight camera? Check out my guide!

Walt2

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 28
  • Posts: 787
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #7 on: May 18, 2013, 06:55:45 PM »

Well, I mean, I do work at X10. :)

Wow, I just got my camera, and with your excellent instructions posted at the top of this thread, I was able to get my camera up and working over the internet, quickly without any not a single problem.



Great job Tony, and thanks!   #:)
Logged
* Sears Home Control System, Radio Shack Plug 'n Power, NuTone, Stanley LightMaker, BSR, HomeLink.
* Tecmar Device Master, CP290 (LightHouse), CM11A (AH), CM14A (AH2), CM15A (AHPro).

Tyler E

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 31
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #8 on: May 20, 2013, 09:56:40 AM »

Well, I mean, I do work at X10. :)

Wow, I just got my camera, and with your excellent instructions posted at the top of this thread, I was able to get my camera up and working over the internet, quickly without any not a single problem.



Great job Tony, and thanks!   #:)
Great! I'm glad you were able to get it going, that's awesome.

If anyone runs into any problems with this guide, by the way, please please point them out to me.
Logged
Having trouble port forwarding your Airsight camera? Check out my guide!

Mud Pie

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 16
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #9 on: May 26, 2013, 02:04:47 PM »

Most excellent write up !!  :)%

I wish it was around when I was doing my, "hmmmm, nope.  Let's try this. Hmmm, nope.  Lemme try THIS..." before I finally got all my cams online !!

 ;D
Logged

bheisler

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #10 on: June 07, 2013, 08:36:20 AM »

I am going nuts.  My IP addresses for cameras are constantly changing, requiring me to re-do the setup info for each camera over and over.  In searching for a cure, it seems to be all Greek to me.  Is there a set of instructions somewhere that I can use to cure this problem?  I am running Windows 7 Home Premium.  Thanks for any help you may be able to provide.  Bernie
Logged

richy2

  • Hero Member
  • *****
  • Helpful Post Rating: 6
  • Posts: 303
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #11 on: June 07, 2013, 03:44:30 PM »

I am going nuts.  My IP addresses for cameras are constantly changing, requiring me to re-do the setup info for each camera over and over.  In searching for a cure, it seems to be all Greek to me.  Is there a set of instructions somewhere that I can use to cure this problem?  I am running Windows 7 Home Premium.  Thanks for any help you may be able to provide.  Bernie
Go to x10 site and download the manual for your camera.

Start there.

nuff said.
Logged

Tyler E

  • Full Member
  • ***
  • Helpful Post Rating: 2
  • Posts: 31
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #12 on: June 10, 2013, 12:31:22 PM »

I also cover that in Step 1: Gather Information and Step 2: Static IP.
Logged
Having trouble port forwarding your Airsight camera? Check out my guide!

Darrel

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #13 on: June 29, 2013, 03:17:00 PM »

Would like to see how to do this on a mac running parallels and windows xp pro
Seems i am having problems getting this done.

Thanks for any help.

I can get it on my network but not outside of it.
« Last Edit: June 29, 2013, 04:33:07 PM by Darrel »
Logged

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: Airsight Remote Viewing Guide (with pictures)
« Reply #14 on: June 29, 2013, 06:02:38 PM »

I can get it on my network but not outside of it.
Have you set up port forwarding through your router?
Logged
"This aftershave makes me look fat"
Pages: [1] 2
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.