Please login or register.

Login with username, password and session length

Author Topic: SR227 breaking plastic plungers  (Read 1905 times)

34Ford

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
SR227 breaking plastic plungers
« on: March 09, 2018, 07:42:31 AM »

I have had one SR227 for years working great then all of the sudden it clicked rapidly and dont work.
Bring it in and tear into it and find the plastic plunger is broke.

Bought 4 more units on Ebay, hooked 2 of them up and and they break their plungers so I am quitting and not trying the rest.

Has anyone tried 3D printing one of these?  I have a printer so I am thinking of trying to make one.  Or should I just go to the pa011?


Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 282
  • Posts: 10497
  • I don't work for X10, I use it successfuly!
Re: SR227 breaking plastic plungers
« Reply #1 on: March 09, 2018, 09:18:52 AM »

The new pa011 from Authinx  is of higher quality.
Since you have a printer try making the part.
However the to me rapid clicking indicates a signal storm and since you already have had two more go it appears the signal storm is still present.
I'd do a bit of investigating to try and find the cause.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: SR227 breaking plastic plungers
« Reply #2 on: March 09, 2018, 10:34:14 AM »

If you print one, save the cad file. I bet you could sell a couple.
Logged
Remote control is cool,

but automation rules!

34Ford

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: SR227 breaking plastic plungers
« Reply #3 on: March 09, 2018, 09:34:45 PM »


However the to me rapid clicking indicates a signal storm and since you already have had two more go it appears the signal storm is still present.
I'd do a bit of investigating to try and find the cause.

Actually I wasn't getting the rapid clicks until after the plunger breaks. I will need to read up on signal storm.

I was reading on the net that the pa011 didn't have the typical CLICK when activating like the SR227 so I was under the impression they didn't use a coil and was possibly better.

« Last Edit: March 09, 2018, 09:38:27 PM by 34Ford »
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 282
  • Posts: 10497
  • I don't work for X10, I use it successfuly!
Re: SR227 breaking plastic plungers
« Reply #4 on: March 09, 2018, 10:03:35 PM »

The new PA011 does still make a click it just isn't as loud (not silent).
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

dave w

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 139
  • Posts: 6116
Re: SR227 breaking plastic plungers
« Reply #5 on: March 09, 2018, 11:36:27 PM »

This has been a recurring problem with the old SR227.
"Old X10" did a bad job on the actuator. The rapid clicking could also be the controller chip re-firing the solenoid because it did not see the change of status on the relay output. Usually this is three rapid fire clicks and then the controller gives up until the next ON (or OFF) X10 command is received.
Logged
"This aftershave makes me look fat"

brobin

  • Hero Member
  • *****
  • Helpful Post Rating: 157
  • Posts: 1406
Re: SR227 breaking plastic plungers
« Reply #6 on: March 10, 2018, 06:09:07 AM »

Many,many years ago I had some SR227's and they all the failed the same way with the triple clicks. I gave up on them and just use the plug-in modules.
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: SR227 breaking plastic plungers
« Reply #7 on: March 11, 2018, 01:13:53 AM »

One possibility.
If it was Off when it broke.
When trying to turn On. It does not go on to the module tries a few more times and then give up. Click click click.
Until you try an On again.

As other have pointed out. The actuator was a sore spot and frequently failed.
Logged

34Ford

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: SR227 breaking plastic plungers
« Reply #8 on: March 18, 2018, 01:29:47 AM »

Well I am not having any luck 3D printing a piece this small.  So probably the best solution is casting a solid piece.

Looking at the Alumilite products now.
Logged

34Ford

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 4
Re: SR227 breaking plastic plungers
« Reply #9 on: March 18, 2018, 01:31:23 AM »

I realized my posts are in the wrong thread. I hardly think this pertains to a X10 airpad.
Logged

Knightrider

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 62
  • Posts: 1748
  • I love my WM100!
    • This Automated House
Re: SR227 breaking plastic plungers
« Reply #10 on: March 18, 2018, 01:43:06 AM »

Nice catch. Is moved.
Logged
Remote control is cool,

but automation rules!
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.