Please login or register.

Login with username, password and session length

Author Topic: How to add ds10 security sensors to HG 1.3  (Read 4688 times)

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
How to add ds10 security sensors to HG 1.3
« on: October 22, 2023, 08:52:12 AM »

Hi
I was given a bunch of da10 security sensors,what I would like to know is, how do I add them to HG 1.3?
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: How to add ds10 security sensors to HG 1.3
« Reply #1 on: October 22, 2023, 03:38:43 PM »

What RF receiver or transceiver  are you trying to use with the DS10A Security Sensors.
The security message is different than other X10 RF devices.
Some may not process them.
My CM15A would with one of the software plug in but my WGL  W800RF32 generated an Unrecognized or Corrupt Packet message.
The message also had different contents in the messages before and after I did a Generate a new security code on the test DS10A.
Logged

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
Re: How to add ds10 security sensors to HG 1.3
« Reply #2 on: October 22, 2023, 05:05:52 PM »

Hi Brian
I am using a cm15a, I installed one sensor in ahp & ahp confirms it, the thing I am having is setting that sensor up in homegenie?
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10522
  • I don't work for X10, I use it successfuly!
Re: How to add ds10 security sensors to HG 1.3
« Reply #3 on: October 22, 2023, 05:37:52 PM »

Hi
I was given a bunch of da10 security sensors,what I would like to know is, how do I add them to HG 1.3?
You need to enable x10 RF in HG then Hg should see the sensors when you press the test button
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
Re: How to add ds10 security sensors to HG 1.3
« Reply #4 on: October 22, 2023, 05:57:42 PM »

Thank you for the response but were do I find how to enable x10RF in 1.3-stable-19? I don't know where to find it?
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: How to add ds10 security sensors to HG 1.3
« Reply #5 on: October 22, 2023, 06:09:44 PM »

Thanks for the information.
Glad you are using an X10 interface that can process it.
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10522
  • I don't work for X10, I use it successfuly!
Re: How to add ds10 security sensors to HG 1.3
« Reply #6 on: October 23, 2023, 01:26:36 PM »

Go to Configure then select your group you wish to add your ds10 sensors to. Select add module and select RF CM15 Tranciever this will add a module that will display incoming RF signals.
When you press the test button on the ds10 the code it sends will be seen, the module display will say Added module S- ......
Click add module again and look for a module that starts wit S-  and ends with x10 security that will be the ds10.
Once added you can name it.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
Re: How to add ds10 security sensors to HG 1.3
« Reply #7 on: October 23, 2023, 02:07:22 PM »

Thank you tuiceman for responding, I am following your instructions but I don't have a module named RF CM15 Transciever?
I believe the problem is X10 RF in snot enabled in HG, I do not know were to enable this in v1.3-stable19? Cab you point me in the right direction to enable X10 RF in this version?
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10522
  • I don't work for X10, I use it successfuly!
Re: How to add ds10 security sensors to HG 1.3
« Reply #8 on: October 23, 2023, 05:10:53 PM »

Is HG seeing the CM15A and x10 working from HG?
If your using AHP on the same PC as Homegenie they use different drivers which can affect performance.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
Re: How to add ds10 security sensors to HG 1.3
« Reply #9 on: October 23, 2023, 06:47:31 PM »

 Yes x10 is working in HG, but HG does not see the CM15A? AHP is running on a win10 computer, HG is running on a RPI 3B.
The problem seems to be that HG is not seeing the CM15A?
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10522
  • I don't work for X10, I use it successfuly!
Re: How to add ds10 security sensors to HG 1.3
« Reply #10 on: October 24, 2023, 11:19:21 AM »

Do you have 2 CM15A or are you swapping the one back and forth?
If you have 2 try switching the one on the pi with the one from the PC.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

spacenut

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 24
Re: How to add ds10 security sensors to HG 1.3
« Reply #11 on: October 24, 2023, 06:52:55 PM »

I only have one cm15a, but I think I have a cm19a lying around here somewhere, would that work if I plugged it into the RPI with is were HG is installed?
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10522
  • I don't work for X10, I use it successfuly!
Re: How to add ds10 security sensors to HG 1.3
« Reply #12 on: October 25, 2023, 07:07:12 AM »

Yes, at least it does on my pi.
You'll need to switch the interface in HG to the cm19.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.