Contact | X10.com
Please login or register.

Login with username, password and session length

Author Topic: CM15a RF problem  (Read 8754 times)

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
CM15a RF problem
« on: May 18, 2006, 06:10:21 PM »
I recently setup a CM15A with several lamp and switch modules and everything is working fine.  Today I received the "stick-a-switch" (SS13A) and an Active Eye motion sensor (MS16A).  I can't get either of these RF modules to work with the CM15A.  I turned on the transcieved house codes in ActiveHome Pro for these modules but nothing seems to work.  I've tried holding the SS13A and MS16A anywhere from 1 inch away from the CM15A to many feet.  Anyone have any ideas?  Do you think I have a bad CM15A?

Thanks,
Greg
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: CM15a RF problem
« Reply #1 on: May 18, 2006, 06:22:57 PM »
Do you have any other remotes that work correctly? Some early cm15as didn't have good RF Range but with them not even doing 1". You may have a bad unit. You did say the tranceived house codes where enabled.
Logged

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #2 on: May 18, 2006, 06:33:54 PM »
No, no other remotes.  Just the motion sensor and stick-a-switch that I got today.  I triple checked that the tranceive codes are selected in AHP.  I guess I'll send an e-mail to service and see what they say.
Logged

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #3 on: May 18, 2006, 06:36:25 PM »
And just to be sure I understand...  If I press a button the switch or the test button on the motion sensor I should see it show up in the AHP activity log right?  (and I checked that the log is set to view RF signals).

Thanks,
Greg
Logged

steven r

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 74
  • Posts: 2189
  • Halloween with X10
Re: CM15a RF problem
« Reply #4 on: May 18, 2006, 06:40:08 PM »
Some "stick-a-switch" units aren't famous for their range either but anything should work near the unit. Did an extra battery come with your "stick-a-switch". The original batteries for mine were nearly dead. Also it seems almost too obvious to mention but double check to make sure that you have set the CM15A to transceive the HC that you're using.
Logged
BVC let's me tell my camera where to go!
:) Murphy is my beta testing pal. He helps me find problems whether I like it or not. :)

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #5 on: May 18, 2006, 06:48:18 PM »
No extra battery with the stick-a-switch, but the LED does glow when I press a button.  And the motion sensor has brand new AAA batteries in it (and I can see that LED glow also).

Thanks,
Greg
Logged

billy

  • Sr. Member
  • ****
  • Helpful Post Rating: 7
  • Posts: 110
Re: CM15a RF problem
« Reply #6 on: May 18, 2006, 08:24:56 PM »
After you set the Transceived House Code(s) did you Download Timers and Macros to the CM15A interface?

Logged
"I would rather live my life as if there is a God and die to find out there isn't, than live my life as if there isn't and die to find out there is."  Albert Camus

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #7 on: May 19, 2006, 07:26:13 AM »
Yup, downloaded to the CM15A after setting the transceived codes.

I contacted technical support and they are going to replace the CM15A.  Looks like I just got a bad unit.

But thanks for all the help everybody.  You all helped me to verify I wasn't missing anything obvious (which I tend to do a lot!).

Thanks,
Greg
Logged

steven r

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 74
  • Posts: 2189
  • Halloween with X10
Re: CM15a RF problem
« Reply #8 on: May 19, 2006, 12:42:08 PM »
Quote from: wazkaren on May 19, 2006, 07:26:13 AM
...I contacted technical support and they are going to replace the CM15A.  Looks like I just got a bad unit....
Let us know when you get the new CM15A. In the meantime you can get everything programed in preparation. :)
Logged
BVC let's me tell my camera where to go!
:) Murphy is my beta testing pal. He helps me find problems whether I like it or not. :)

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #9 on: May 19, 2006, 08:28:54 PM »
I borrowed a friends X10 RF receiver and it works fine with both the motion sensor and the stick-a-switch, so I guess that confirms a problem with the CM15A.

Tech support responded to my e-mail in less than an hour with an RMA to replace the unit.  It's unfortunate that I have to eat the cost of shipping but tech support was quite good.

Greg 
Logged

roger1818

  • Hero Member
  • *****
  • Helpful Post Rating: 28
  • Posts: 1072
  • Roger H.
Re: CM15a RF problem
« Reply #10 on: May 25, 2006, 10:46:10 AM »
Quote from: wazkaren on May 19, 2006, 08:28:54 PM
It's unfortunate that I have to eat the cost of shipping but tech support was quite good.

If you complain, you should be able to get them to pay for shipping, especially since it was DOA.
Logged

Duke

  • Newbie
  • Helpful Post Rating: 0
  • Posts: 2
Re: CM15a RF problem
« Reply #11 on: June 04, 2006, 12:37:10 AM »
Some times you can unplug and remove the batteries and let the cma15a set for 30 min and it will start working again. I had the same problem and also got a RMA# but tried the unit again and it works still. That was about a month ago, so some times it just needs a rest to get it back to working.
Logged

nklght

  • Sr. Member
  • ****
  • Helpful Post Rating: 2
  • Posts: 126
Re: CM15a RF problem
« Reply #12 on: June 22, 2006, 12:48:19 AM »
Quote
Some times you can unplug and remove the batteries and let the cma15a set for 30 min and it will start working again. I had the same problem and also got a RMA# but tried the unit again and it works still. That was about a month ago, so some times it just needs a rest to get it back to working.

Did you return the unit?  The cm15a is supposed to work 24/7/365, if it stops working then their is a problem with the unit.  By giving it a rest, you just prolonged the point of final failure.  The cm15a is an electronic device and the usuall cause for an electronic device to quit working and then start working after a period of rest is that it has overheated.  Even if you got it to start working again, the units life span has been shortened, and the next time it goes out the warranty might expire.  Smell the unit, if it is an overheating issue, then their will be a pungent odor coming from the unit.  Also if you bought a car and it stopped working and the dealer agreed to take it back and give you a new one since it was under warranty, the next morning the car starts working like it should, what would you do?  Do you return the car since it is not functioning like it should all the time and is unreliable, or do you keep it since it started working the next day     
Logged

wazkaren

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 23
Re: CM15a RF problem
« Reply #13 on: June 23, 2006, 06:07:16 PM »
Quote from: nklght on June 22, 2006, 12:48:19 AM
Did you return the unit? 

Yup, returned it and got a replacement.  The new one works fine so it was a faulty unit. 

Thanks,
Greg
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.