Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[emil]

I thought we could do this?

This is what I have:

A1 is an RF signal

(A1 macro)
A1 on
    Appliance B1 on
A1 off
    Appliance B1 off

(B1 macro)
B1 on
    Lights on, etc...
B1 off
    Lights off, etc...

B1 macro on/off is successfully called from a timer but not from the A1 RF.

When I look at the Activity Monitor I see A1 and some response that the macro is being called (don't remember exactly what) but then it never executes the macro, I don't see any commands called.

Any ideas or is this expected?

BTW I'm looking at WebIO and would like to have this functionality for it.

Thanks

[Noam]

Out of the box, you can't call one macro from another in AHP.
The trick is to create a "dummy" appliance module on the same HouseCode/UnitCode as the second macro, and have the first macro call THAT.  It looks like you may have already done that.
The other thing you'll need to do is to make sure that HouseCode "B" is checked in the "Transceived House Codes" box in the Hardware Configuration.

[emil]

Out of the box, you can't call one macro from another in AHP.
The trick is to create a "dummy" appliance module on the same HouseCode/UnitCode as the second macro, and have the first macro call THAT.  It looks like you may have already done that.
The other thing you'll need to do is to make sure that HouseCode "B" is checked in the "Transceived House Codes" box in the Hardware Configuration.

B1 is the "dummy" but I'll make sure that "B" is checked as a transceived code.
I need to check exactly what the Monitor is telling me also.
Thanks for the help.

[emil]

SUCCESS     

NOTE:
A Macro can call a Macro UNLESS the called Macro is also attached to a timer!!!

[emil]

Last thing to say on this.

In summary the first thing I tried was:

Dusk Timer -> Nighttime Macro(E9)
RF Button ON -> D1 ON(dummy module) -> Nighttime Macro(E9)

RF Button ON would never execute the macro even though the Activity Monitor showed RF A1 ON, E9 ON(Nighttime Macro) but nothing further.

I figured I'd add a level of indirection on the Timer so I tried this:

Dusk Timer -> D1 ON(dummy module) -> Nighttime Macro(E9)
RF Button ON -> D2 ON(dummy module) -> Nighttime Macro(E9)

Same result as above.

Then I replaced Nighttime Macro with another with the same contents Nighttime Macro #2, it all worked!

Dusk Timer -> Nighttime Macro(E9)
RF Button ON -> D1 ON(dummy module) -> Nighttime Macro #2(E9)

The dummy modules used Appliance Modules to call the Macro.
All used channels are transceived.

There seems to be some tie to the final Macro attached to a timer although I would not expect the processing to be so extensive.

Maybe when I removed the timer from Nighttime Macro and tied it to D1 ON I didn't really remove it?

If time permits I'll continue, otherwise two Nighttime Macro's are not so bad either .

[HA Dave]

Maybe when I removed the timer from Nighttime Macro and tied it to D1 ON I didn't really remove it?

That is possible! To be sure any macro or device is removed you must first (after deleting) empty the trash bin..., clear the CM15A, then reload.

[emil]

Maybe when I removed the timer from Nighttime Macro and tied it to D1 ON I didn't really remove it?

That is possible! To be sure any macro or device is removed you must first (after deleting) empty the trash bin..., clear the CM15A, then reload.

I went and emptied the trash and same result.
When I get some time I'll just make a simple test case but right now it's working great, on to other things!
Thanks for the suggestions.