Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Grem126]

I have a feeling this has been asked before...but here goes.....Is templinc supported by ActiveHome or is there any documentation in the SDK ?

Thanks in advance

[Dan Lawrence]

Smarthome sells it and even though it uses X10 signals, what documentation is on the Smarthome site says it uses all addresses on a housecode, but not what housecodes it uses.    If the housecode range is the standard A-P it might be usable under AHP. Perhaps Smarthome will tell you what housecodes it uses.

[Charles Sullivan]

I have a feeling this has been asked before...but here goes.....Is templinc supported by ActiveHome or is there any documentation in the SDK ?

Thanks in advance

Not through the ActiveHome Pro GUI.  I have no idea what might be done with the SDK.

Dan:
The TempLinc can use any housecode A-P.  It reports a temperature by encoding it as a combination of a unit code 11-16 and a preset dim level 1-32 through the simple formula:
  temperature = -60 + 32*(unit - 11) + (preset_level - 1)

[Dan Lawrence]

I have a feeling this has been asked before...but here goes.....Is templinc supported by ActiveHome or is there any documentation in the SDK ?

Thanks in advance

Not through the ActiveHome Pro GUI.  I have no idea what might be done with the SDK.

Dan:
The TempLinc can use any housecode A-P.  It reports a temperature by encoding it as a combination of a unit code 11-16 and a preset dim level 1-32 through the simple formula:
  temperature = -60 + 32*(unit - 11) + (preset_level - 1)

Thanks, Charles.   That's something I won't be buying.

[Brian H]

It is supposed to act like an RCS TX15B Automation Thermostat. So if the software supported that protocol then it should work. I believe AHP doesn't understand the protocol.

[Human250]

FYI to this thread: I have been using TempLinc succesfully with AHP as a thermostat trigger for macros. 

However, I would like to be able to view temperature information reported by the TempLinc in AHP.  Since TempLinc reports temperature as a housecode + dimmer level this should be possible by setting up a few dummy dimmer module(s) set to the correct house code(s) to read what TempLinc reports.  So if TempLinc reports a dimmer level of 58% on A14, I would know the temp is 54 degrees F.  I have not been able to read TempLinc this way thus far and I suspect this has to do with which phantom module to use.  I do have the House Code monitoring the same letter as the TempLinc and I do see some activity in the activity monitor, but for some reason this is not being 'seen' by the phantom dimmer module. Do you have any useful tips I could apply? Thanks.

[Charles Sullivan]

FYI to this thread: I have been using TempLinc succesfully with AHP as a thermostat trigger for macros. 

However, I would like to be able to view temperature information reported by the TempLinc in AHP.  Since TempLinc reports temperature as a housecode + dimmer level this should be possible by setting up a few dummy dimmer module(s) set to the correct house code(s) to read what TempLinc reports.  So if TempLinc reports a dimmer level of 58% on A14, I would know the temp is 54 degrees F.  I have not been able to read TempLinc this way thus far and I suspect this has to do with which phantom module to use.  I do have the House Code monitoring the same letter as the TempLinc and I do see some activity in the activity monitor, but for some reason this is not being 'seen' by the phantom dimmer module. Do you have any useful tips I could apply? Thanks.

The basic problem is that the TempLinc reports temperature by encoding it as a unit code and Preset Dim level, not a "regular" dim level.  (See my May 07, 2008 message in this thread.)
As of the last time I looked, AHP did not support the Preset  Dim codes.

[Boiler]

FYI to this thread: I have been using TempLinc succesfully with AHP as a thermostat trigger for macros. 

However, I would like to be able to view temperature information reported by the TempLinc in AHP.  Since TempLinc reports temperature as a housecode + dimmer level this should be possible by setting up a few dummy dimmer module(s) set to the correct house code(s) to read what TempLinc reports.  So if TempLinc reports a dimmer level of 58% on A14, I would know the temp is 54 degrees F.  I have not been able to read TempLinc this way thus far and I suspect this has to do with which phantom module to use.  I do have the House Code monitoring the same letter as the TempLinc and I do see some activity in the activity monitor, but for some reason this is not being 'seen' by the phantom dimmer module. Do you have any useful tips I could apply? Thanks.

Wow Charles, you're quick...

As Charles indicated, AHP does not understand the Smarthome Version of Preset-Dim.  This was part of the X10 protocol that was re-defined many years ago.  Smarthome picked up the "old" preset dim1 and dim2 method.  X10 never implemented these - they went to the extended code protocol instead.



From the graphic above (thanks to Uncle Phil) you can see that the Preset Dim1 and Dim2 no longer exist in X10's definition.

Now for the twist, although AHP doesn't understand the Preset Dim1 and 2, the CM15a does and can transmit Dim1 and Dim2 codes via the SDK.  I have never tried the receive function for these.  Not sure if the SDK is an option for you.

[Brian H]

I believe Smarthome has also discontinued the TempLinc as I can no longer find it on their site.