Please login or register.

Login with username, password and session length

Author Topic: LM465 and Halogene lamp(110V Bulb)  (Read 8118 times)

marineau

  • Hero Member
  • *****
  • Helpful Post Rating: 2
  • Posts: 162
LM465 and Halogene lamp(110V Bulb)
« on: October 22, 2006, 03:32:58 PM »

I tried to operate a Halogene lamp(110V Bulb) and a Fluorescent fixture(40 Watts) with my old LM465.
All run Fine !!! (no heat).

But why does its not recommanded to install these fixtures on LM465 ?
Logged

KDR

  • Hero Member
  • *****
  • Helpful Post Rating: 53
  • Posts: 758
    • Home Automation Chat
Re: LM465 and Halogene lamp(110V Bulb)
« Reply #1 on: October 22, 2006, 03:44:58 PM »

The LM465 is a dimable light module and shouldn't be used on a fluorescent light (transformer inside). Also allot of halogene lights have transformers in them which can't be dimmed by the module.

I don't know if anyone has tested the LM465 on these types of lights if the module is set to full (100% bright) and left there long term.
« Last Edit: October 22, 2006, 03:49:04 PM by KDR »
Logged
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

Charles Sullivan

  • Hero Member
  • *****
  • Helpful Post Rating: 94
  • Posts: 1565
    • HEYU - X10 Automation for Linux, Unix, and Mac OSX
Re: LM465 and Halogene lamp(110V Bulb)
« Reply #2 on: October 22, 2006, 03:58:22 PM »

I tried to operate a Halogene lamp(110V Bulb) and a Fluorescent fixture(40 Watts) with my old LM465.
All run Fine !!! (no heat).

But why does its not recommanded to install these fixtures on LM465 ?

Inadvertently dimming a Lamp Module connected to a transformer or ballast could cause these components to overheat.



Logged
Yesterday it worked.
Today it doesn't work.
X10 on Windows is like that.

HEYU - X10 Automation for Linux, Unix, and Mac OS X     http://www.heyu.org

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: LM465 and Halogene lamp(110V Bulb)
« Reply #3 on: October 22, 2006, 04:12:17 PM »

If the halogene light is 120 volt filament and not a transformer type. The LM465 should have no problems. Two wire Wall Switches; that dim and not a relay type; steal power through the light could in some situations have a problem. Due to the lights higher resistance.
Fluorescent with a older ballast or a low voltage transformer light could damage the Lamp Module or the light itself. New electronic ballasts are no better with dimming modules.

Now dimable CFLs that I have tried will work in the lamp module but not wall switches. I also found the plain X10 Lamp Module worked much better than a fancy one with a slow ramp up and down with dimming CFLs.
Logged

marineau

  • Hero Member
  • *****
  • Helpful Post Rating: 2
  • Posts: 162
Re: LM465 and Halogene lamp(110V Bulb)
« Reply #4 on: October 22, 2006, 05:53:52 PM »

Now dimable CFLs that I have tried will work in the lamp module but not wall switches. I also found the plain X10 Lamp Module worked much better than a fancy one with a slow ramp up and down with dimming CFLs.
Scuse me I don't understand few words (I'm french), I am ignorant sometimes !

When you write CFLs, what do you mean ?
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: LM465 and Halogene lamp(110V Bulb)
« Reply #5 on: October 22, 2006, 06:51:32 PM »

Compact Fluorescent Light Bulb. Energy saving type bulb. I use them all over the house. Like a 13Watt is about the same light as a 60 Watt regular incandescent light. Many are a spiral tube like a cork screw and screw into the standard light socket.
No not ignorant. Many of my work customers are from other countries and clarifying things is no problem.
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.