Please login or register.

Login with username, password and session length

Author Topic: House Code A & M  (Read 6113 times)

craig-o

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 13
House Code A & M
« on: December 01, 2006, 01:57:44 PM »

I'm relatively new to X-10 and have been reading quite a bit here and on other forums.  I ran across this posting http://forums.accessx10.com/showthread.php?s=&threadid=253 and was struck by number 10 - "Don't use house code A or M".  The post didn't provide any explanation so I thought I'd ask why it would say to stay away from code A and M? 

Thanks!
Logged

Puck

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 171
  • Posts: 1799
Re: House Code A & M
« Reply #1 on: December 01, 2006, 02:18:01 PM »

House Code A:  When batteries start to die on motion sensors, the motion sensor will reset itself to House Code A, Unit Code 1. So actually, A1 & A2 should be avoided for modules that could accidentally be turned on / off because of this. As well, because this is the default setting for all new stuff, another module may still have the same address (maybe even a neighbour).

House Code M: Most unreliable because the 4 bits are all Zeros. Also, if the House Code selector switch were to fail (in the open state) the default house code becomes M. So for this same reason, Unit Code 13 can experience the same problem.

So if you have a module on M13... well your just asking for trouble.   ;) ;D :D
(Especially if you have an AHP Macro triggering it on[/b][/color] A1:P)
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: House Code A & M
« Reply #2 on: December 01, 2006, 04:21:29 PM »

OH Yes. M13. The code I use when I have modules apart for testing and no wheels are connected. ::)
Logged

Dan Lawrence

  • Hero Member
  • *****
  • Helpful Post Rating: 68
  • Posts: 3991
Re: House Code A & M
« Reply #3 on: December 01, 2006, 10:55:10 PM »

I'm relatively new to X-10 and have been reading quite a bit here and on other forums.  I ran across this posting http://forums.accessx10.com/showthread.php?s=&threadid=253 and was struck by number 10 - "Don't use house code A or M".  The post didn't provide any explanation so I thought I'd ask why it would say to stay away from code A and M? 

Thanks!

I don't use housecode M, but I have Housecode A in use since the earliest X10 days. The Living Room, Bathroom and Bedroom lights are all on A withhout a single problem ever.

Whoever posted on accessx10.com about never using housecode A for anything does not know what he's talking about, at least about A.
Logged
I don't SELL this stuff... BUT I sure do ENJOY using it!!!

TakeTheActive

  • Hero Member
  • *****
  • Helpful Post Rating: 126
  • Posts: 1047
  • Old !@#$% Tinkerer!
Re: House Code A & M
« Reply #4 on: December 02, 2006, 03:12:34 AM »


House Code A:  When batteries start to die on motion sensors, the motion sensor will reset itself to House Code A, Unit Code 1. So actually, A1 & A2 should be avoided for modules that could accidentally be turned on / off because of this. As well, because this is the default setting for all new stuff, another module may still have the same address (maybe even a neighbour).

House Code M: Most unreliable because the 4 bits are all Zeros. Also, if the House Code selector switch were to fail (in the open state) the default house code becomes
M. So for this same reason, Unit Code 13 can experience the same problem.

So if you have a module on
M13... well your just asking for trouble.   ;) ;D :D(Especially if you have an AHP Macro triggering it on[/b][/color] A1:P)

Excellent, complete, nicely-formatted ;) answer, IMHO...
Logged
Low Post Count != Low Knowledge - High Post Count != High Knowledge ;)

ADVICE TO X-10 NEWBIES FROM AN X-10 OLD-TIMER

TakeTheActive

  • Hero Member
  • *****
  • Helpful Post Rating: 126
  • Posts: 1047
  • Old !@#$% Tinkerer!
Re: House Code A & M
« Reply #5 on: December 02, 2006, 03:15:14 AM »


OH Yes. M13. The code I use when I have modules apart for testing and no wheels are connected. ::)

Is there another ECHO ECHO ECHO ECHO ECHO ECHO ECHO ...in here? ;)
Logged
Low Post Count != Low Knowledge - High Post Count != High Knowledge ;)

ADVICE TO X-10 NEWBIES FROM AN X-10 OLD-TIMER

TakeTheActive

  • Hero Member
  • *****
  • Helpful Post Rating: 126
  • Posts: 1047
  • Old !@#$% Tinkerer!
Re: House Code A & M
« Reply #6 on: December 02, 2006, 03:27:41 AM »


I don't use housecode M, but I have Housecode A in use since the earliest X10 days. The Living Room, Bathroom and Bedroom lights are all on A withhout a single problem ever.
Whoever posted on accessx10.com about never using housecode A for anything does not know what he's talking about, at least about A.

  • OPEN MOUTH
    .
  • INSERT FOOT (once again... ::) )

How can you possibly make this statement *AFTER* reading Puck's EXCELLENT reply? ??? :-[
Logged
Low Post Count != Low Knowledge - High Post Count != High Knowledge ;)

ADVICE TO X-10 NEWBIES FROM AN X-10 OLD-TIMER

craig-o

  • Jr. Member
  • **
  • Helpful Post Rating: 0
  • Posts: 13
Re: House Code A & M
« Reply #7 on: December 02, 2006, 09:47:17 AM »

Thanks to all who have responded.  I am a little confused by one thing though.

Quote
House Code A:  When batteries start to die on motion sensors, the motion sensor will reset itself to House Code A, Unit Code 1. So actually, A1 & A2 should be avoided for modules that could accidentally be turned on / off because of this. As well, because this is the default setting for all new stuff, another module may still have the same address (maybe even a neighbour).

I get almost everything here except why A2 is added.  I understand the reseting to default settings when batteries fail issue, but unless I'm just not reading something right here, I can't see how A2 comes into the mix.

Thanks again all!!
Logged

KDR

  • Hero Member
  • *****
  • Helpful Post Rating: 53
  • Posts: 758
    • Home Automation Chat
Re: House Code A & M
« Reply #8 on: December 02, 2006, 10:22:16 AM »

Motion sensors respond 2 ways. Motion and dusk/dawn. A default rest puts it at A1 for motion. The dusk/dawn is always the motion code plus 1 so default motion is A1 and dusk/dawn would be A2. (its automatic)

Hope that helps
Logged
Note: "Guests" may read the X10 forum , but you must register to post!

When I'm online you can find me in the Home Automation Chat Room!

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13295
Re: House Code A & M
« Reply #9 on: December 02, 2006, 11:54:37 AM »

I also use A with no problems. I also like not having to reprogram remotes from the dead battery A as that is the default.
That said if I had motion sensors A would most likely not be my code of choice. Every set up is different so one perons problem is not another's.
Logged

vhoang

  • Sr. Member
  • ****
  • Helpful Post Rating: 7
  • Posts: 107
    • Automation Tips & Mini DLLs
Re: House Code A & M
« Reply #10 on: December 02, 2006, 03:33:02 PM »

I also use A with no problems. I also like not having to reprogram remotes from the dead battery A as that is the default.
That said if I had motion sensors A would most likely not be my code of choice. Every set up is different so one perons problem is not another's.

I use A1 for the same reason.  I don't respond to A1-AOff.  I let a timer countdown turn it off.  Non critical stuff considering the possible side effects mentioned above.

Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.