Contact | X10.com
Please login or register.

Login with username, password and session length

Author Topic: Big Red Panic Button  (Read 6128 times)

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Big Red Panic Button
« on: January 22, 2008, 12:51:37 PM »
I want the Big Red Panic Button to talk directly to the CM15A, as i want to use it as a door bell of sorts if i can get it to work...

The one i have does not talk direct no matter how much i play with it or recode it....any idea or suggestions.

Andrew
Logged

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Big Red Panic Button
« Reply #1 on: January 22, 2008, 01:27:52 PM »
Quote from: Rockhoppers on January 22, 2008, 12:51:37 PM
I want the Big Red Panic Button to talk directly to the CM15A, .........

I am not sure what.. "talk directly" means. However... if you set the Big Red Button to a H/U code.. then select/assign a 2-pin appliance module to the same code in AHP. (You don't need to actually have an appliance module, as this is a ghost.) DO make sure this is a TRANSCEIVED house code.

Then setup your macros... and timed off events for the appliance module. As the Big Red Button ONLY sends an ON signal.
Logged
Home Automation is an always changing technology

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Re: Big Red Panic Button
« Reply #2 on: January 22, 2008, 01:35:08 PM »
apologies, obviously in to much of a hurry to say what i was trying to get across.

I am developing a "ground up" program using the SDK......

The button has been assigned code B1, but while all the other items send a signal to the CM15A without isue, the button does not....

I just want the CM15A to get an on signal, that is all.... nothing complicated, the switching will be done by the program based on a couple of other conditions.

Is it me, or is it maybe the unit ? should the CM15A see the button when it is pressed ?

Andrew
Logged

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Big Red Panic Button
« Reply #3 on: January 22, 2008, 02:59:19 PM »
You may want to check the button using an old-fashion transceiver... and a chime or module. It could just be the battery is dead.
Logged
Home Automation is an always changing technology

Walt2

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 28
  • Posts: 787
Re: Big Red Panic Button
« Reply #4 on: January 22, 2008, 08:42:00 PM »
One could also run the Activity Monitor on AHP, and see what it reports when one presses the Big Red Button.
Logged
* Sears Home Control System, Radio Shack Plug 'n Power, NuTone, Stanley LightMaker, BSR, HomeLink.
* Tecmar Device Master, CP290 (LightHouse), CM11A (AH), CM14A (AH2), CM15A (AHPro).

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Re: Big Red Panic Button
« Reply #5 on: January 23, 2008, 04:14:18 AM »
I tried that, no report !

Thats what prompted the question.

Andrew
Logged

steven r

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 74
  • Posts: 2189
  • Halloween with X10
Re: Big Red Panic Button
« Reply #6 on: January 23, 2008, 12:16:36 PM »
Just to rule out a signal range issue, have you watched the AHP activity monitor while  holding the Big Red Button near to the CM15A?
(X10 transmitters and the CM15A aren't famous for their distance range.)
« Last Edit: January 23, 2008, 12:18:12 PM by steven r »
Logged
BVC let's me tell my camera where to go!
:) Murphy is my beta testing pal. He helps me find problems whether I like it or not. :)

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Re: Big Red Panic Button
« Reply #7 on: January 23, 2008, 01:54:24 PM »
Yes, done that.... the big red button is on the desk, right next to the CM15A.... which does have a poor range, but it think it should handle 6 inches ! !

Intend to modify the CM15A antenna as soon as i get it all working on the desk.

Thanks

Andrew
Logged

steven r

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 74
  • Posts: 2189
  • Halloween with X10
Re: Big Red Panic Button
« Reply #8 on: January 23, 2008, 02:18:46 PM »
Quote from: Rockhoppers on January 23, 2008, 01:54:24 PM
Yes, done that.... the big red button is on the desk, right next to the CM15A.... which does have a poor range, but it think it should handle 6 inches ! !...
Do you have any other transmiting device to check if the CM15A is not receiving?
Any other receiving device like Dave_x10_L suggested to make sure the button is transmitting?

My bet is that the button is defective.
Logged
BVC let's me tell my camera where to go!
:) Murphy is my beta testing pal. He helps me find problems whether I like it or not. :)

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Re: Big Red Panic Button
« Reply #9 on: January 23, 2008, 02:36:09 PM »
No other receiving device, but i do have a key pad a three motion detectors that are all tansmitting to the CM15A just fine...

It does say on the literiture for the button that is should, and i quote "tramsmit to an X10 Trasceiver (RR501 or TM751)" but no mention of a CM15A !

So i may be on a loser from the start !

Andrew
Logged

steven r

  • Advanced Member
  • Hero Member
  • ******
  • Helpful Post Rating: 74
  • Posts: 2189
  • Halloween with X10
Re: Big Red Panic Button
« Reply #10 on: January 23, 2008, 02:55:58 PM »
Quote from: Rockhoppers on January 23, 2008, 02:36:09 PM
...It does say on the literature for the button that is should, and i quote "transmit to an X10 Transceiver (RR501 or TM751)" but no mention of a CM15A !...
It should work with the CM15A! Most likely the only reason the CM15A isn't mentioned in the literature is because the literature came out before the CM15A.

Quote from: Rockhoppers on January 23, 2008, 02:36:09 PM
...i do have a key pad a three motion detectors that are all transmitting to the CM15A just fine...
Your button is defective. Call X10 and tell them you have watched the activity monitor in AHP and while it displays signals from several detectors you have, it displays no signal from your "Big Red Button". Also mention you have tried a new battery in the button.

Logged
BVC let's me tell my camera where to go!
:) Murphy is my beta testing pal. He helps me find problems whether I like it or not. :)

Rockhoppers

  • Full Member
  • ***
  • Helpful Post Rating: 0
  • Posts: 29
Re: Big Red Panic Button
« Reply #11 on: January 23, 2008, 03:00:53 PM »
Yup, i think that is my only option, just wanted to bounce it off a few people to make sure i was not missing anything to obvious.

Cheers

Andrew
Logged
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.