Dave, I replaced the Surge protector with a new one, Didnt help. But noticed something else, I can control those lamps with the wired controller in the bedroom.
but not from AHP or remote, So just for fun I plugged the RR501 next to the Lamp Module, I can control the lamps now from the remote,but they have about a 5 second delay.
I'm going to problem solve as I describe the house layout for you.
This is a mobile home so lets say the wall with the couch is the right side wall, The AHP, CM15A is on the left side wall, both are in the living room, The wired controller is on the left wall in the bedroom, The Breaker panel is in the bedroom on the right side wall. I'm Assumeing that you are correct in that the couch lamps, porch, are all on the same breaker and probably the outlet with my wifes computer and landline wireless phones. there is only 8 outlet plugs on the right wall from one end of the trailer to the other. the front door is on the right wall, on the right side of the door is 3 wall switches, first switch is for the porch light, second switch is for the wall outlet behind the leftside of the couch. The third switch is for the ceiling fan.
The ceiling fan has five lights but non of them are CFLs/LEDs. The only CFLs in the house are in the porch light and in the kitchen light fixtures. But am I wrong in assuming that the lights have to be on for them to cause a problem? one of the light switches on the right wall controls a set of CFLs in the kitchen and next to the switch is a wall outlet that is empty (nothing is plugged in) the other outlets on that wall have the microwave and toaster oven plugged in the last outlet has the fridge plugged in.
But I'm getting off track here, I was going to say that its just at night but I havent been able to control them today until I plugged in the RR501, So I walked through the house looking at all the power outlets on the right wall. in the front bathroom is a hair dryer and a frebreeze air freshener, I unplugged it and checked to see if I could turn on the lamps, Still a delay. The ONLY thing thats was on in my daughters room was a LED night light that changes colors so I unplugged it and ran my check, the lights came on with out a delay, so I tried the porch light and it came on without a delay. so I came into the kitchen and plugged the night light into the outlet so it would be between the problem module and the breaker box. I tried to turn on the lamps, They came on but I couldnt turn them off, I unplugged the night light and they went off with no delay. So I thought I had it fixed but noticed that I still cant control the lights with the CM15A. Just checked the find other computers its now showing house code N all yellow except N12 is red saying it received a code a few minutes ago while I was testing mine. I have nothing on house code N or on unit code 12.
Something is blocking the signal from the CM15A, so what Im trying to figure out is whats between the Interface and the wired controller, but thats not right ether because I can control the fans in the bedroom thats on the same wall as the couch and breaker box. The outlets between the interface and the breaker box, one has a dishwasher and a convection oven plugged in, then another has a chest type freezer, then in the utility room is the washer and dryer, the dryer is wired for 220, the AC is wired in to a breaker outside. two light switches one for the back light porch and the the utility room ceiling light. all have normal bulbs, the next room is the bedroom, light switch that control ceiling fan with normal bulbs, wall outlet with wife's alarm clock plugged in it, then you got the left wall with 2 outlets, one has a lamp module for the night stand lamps (no problems) the other has the wired controller and my alarm clock, the bathroom is last with light switch normal lights and a outlet with a wireless phone and blow dryer. then the closet with a pull chain light and the breaker box on the right wall, We have two more outlets one with two appliance modules (no problems) the next outlet has my computer and wireless landline phone. back to the kitchen wall, I put a appliance module into the empty outlet and could control it without a delay, using the remote has a 3 second delay, the next outlet is the one with my wifes laptop then were back to the problem module.
I think I'm going to move the problem module to that outlet and see if it makes a difference. I moved it I can control them now with the CM15A but still have no control over the porch light with the CM15A, So I would say that the problem is going to be on the porch, The porch has a appliance module controlling a CFL bulb and 2 video cameras, one with a Ninja and the RR501 is also plugged in on the porch. I would say the RR501 is whats allowing me to control the porch light. looks like I will be going around unplugging camera power supplies and testing. I dont think its the CFL because its not on, I Will let you know what I find.
Author
Topic: Everything has stopped working, after 2 years of great service. (Read 25678 times)