Please login or register.

Login with username, password and session length
Pages: 1 2 [3] 4 5

Author Topic: Can not connect wifi Unit WM100  (Read 36402 times)

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #30 on: February 11, 2018, 12:45:12 PM »

OK missed the appliance module As I don't recognized it with the cover.
Have you tried a lamp module in place of the appliance module?


Logged
Please Read Topic:
General Forum Etiquette
Before you post!

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #31 on: February 11, 2018, 12:46:21 PM »

yes tried more then a few..lol....
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #32 on: February 11, 2018, 12:54:01 PM »

Have you tried a wifi module hard reset and app factory reset?
Since the module seems to be seeing the signal I don't think it is the app but you could try a reinstall of it.
Have you tested with another phone or tablet?
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #33 on: February 11, 2018, 12:55:50 PM »

yes the initial install would not work with my Samsung phones but worked with iPad, will try a reset on both..
Logged

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #34 on: February 11, 2018, 01:01:51 PM »

yep no luck, good thing I have a box big enough for both X10 wifi units  :-[
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #35 on: February 11, 2018, 01:05:16 PM »

Have you tried the Samsung phones after initial setup and tell them to connect to an existing hub?
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #36 on: February 11, 2018, 01:07:17 PM »

yes sir, did that;  they see the modules I installed but nothing turns on or off...
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #37 on: February 11, 2018, 01:09:36 PM »

 B:(
Ok let me fire off a email see if Authinx has any suggestions.
Usually they test the replacement units before sending them out.
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #38 on: February 11, 2018, 01:30:34 PM »

hold on a sec.... i just tried this... i have a few  filters XPPF ....
ok so a bit of a success, but nothing I can do yet, so i install XPPF module into the wall I then plug in power bar strip I plug in x10 wifi unit and lamp in same strip and it works but outside the power bar stip nothing works...

so i plug in my  tm751 on other side of room and use remote and it turns everything on, if its a house wiring then nothing should work correct, its like there is not enough power(signal strength) in the wifi unit.
« Last Edit: February 11, 2018, 01:33:26 PM by astrothug »
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #39 on: February 11, 2018, 01:37:26 PM »

Ok so the Wi-Fi unit does work to a degree.
Maybe Jeff can chime in with some tests for you to try.
I'm still going to see if Authinx has any suggestions have you tested the outlets to be sure they're wired correctly?
https://www.amazon.ca/Sperry-Instruments-GFI6302-Receptacle-Professional/dp/B000RUL2UU/ref=sr_1_8?ie=UTF8&qid=1518394806&sr=8-8&keywords=electrical+wire+tester

Logged
Please Read Topic:
General Forum Etiquette
Before you post!

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #40 on: February 11, 2018, 01:42:05 PM »

my house as been rewired last year when i switched from gas heat to electric base heaters, .... i was using my cm15a in the same spot as the wifi unit and had no issues with the house wiring. infact i didn't even use the filters...
Logged

Tuicemen

  • Administrator
  • Hero Member
  • ****
  • Helpful Post Rating: 283
  • Posts: 10509
  • I don't work for X10, I use it successfuly!
Re: Can not connect wifi Unit WM100
« Reply #41 on: February 11, 2018, 01:49:42 PM »

Your Outlet in the video is Upside down from the way outlets are usually installed with an electrical rewire. (At least in Ontario Canada)
Logged
Please Read Topic:
General Forum Etiquette
Before you post!

HA Dave

  • Hero Member
  • *****
  • Helpful Post Rating: 175
  • Posts: 7127
Re: Can not connect wifi Unit WM100
« Reply #42 on: February 11, 2018, 02:07:04 PM »

here is a video....  B:( B:( https://youtu.be/SOunbZbGmgs

Oh for God's sake man.... there isn't anything pluged into the module!

Your "listening for the transceiver to click" and it only does that when triggered by RF. The WM100 is PLC. Plug a light or radio or soemthing into the module (NOT the one with the antennaa) and let your WM100 turn it on/off.
« Last Edit: February 11, 2018, 02:09:08 PM by HA Dave »
Logged
Home Automation is an always changing technology

JeffVolp

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 122
  • Posts: 2299
    • XTB Home Page
Re: Can not connect wifi Unit WM100
« Reply #43 on: February 11, 2018, 02:08:50 PM »

hold on a sec.... i just tried this... i have a few  filters XPPF ....
ok so a bit of a success, but nothing I can do yet, so i install XPPF module into the wall I then plug in power bar strip I plug in x10 wifi unit and lamp in same strip and it works but outside the power bar stip nothing works...

That is indicative of powerline noise.  Isolating the power strip prevented powerline noise from blocking the appliance module from decoding the command.

Another test you could do is plug the power strip and WM100 into an outlet on another circuit located a distance from the panel.  Assuming that also works, check the circuit you had been using for a potential noise generator.  The usual causes are a plug-in power module or a CFL or LED light.

Once you identify the problem you can isolate that device with the filter and plug the WM100 back into the wall outlet so it can send commands throughout your home.  (You may need a good tuned-circuit signal coupler to propagate signals to the opposite phase if you do not already have one.)

Jeff

Logged
X-10 automation since the BSR days

astrothug

  • Hero Member
  • *****
  • Helpful Post Rating: 4
  • Posts: 153
Re: Can not connect wifi Unit WM100
« Reply #44 on: February 11, 2018, 02:08:55 PM »

ok i ordered the thing, after looking at my cm15a it too has issues with lines in the same spot, so i moved it it was able to turn lights on across the room, I then used my  tm751 in the same plug it to had no issues, from the same spot i then pluged in VM100 and nothing happens it registered that a signal was sent but nothing happens going to unplug everything and retest.
Logged
Pages: 1 2 [3] 4 5
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.