Please login or register.

Login with username, password and session length
Pages: 1 [2]

Author Topic: Hybrid Setup?  (Read 7866 times)

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Hybrid Setup?
« Reply #15 on: November 03, 2010, 12:46:18 PM »

Interesting log entries.
Not sure exactly what they indicate.
Logged

Brandt

  • Hero Member
  • *****
  • Helpful Post Rating: 11
  • Posts: 728
  • Sorry miss, I was giving myself an oil-job.
Re: Hybrid Setup?
« Reply #16 on: November 03, 2010, 01:08:28 PM »

Basically they indicate that there are some communication errors with the switch when the switch is off.
It's as if it responds to a status request too quickly for the CM11a to process.

The above post was output on the command line. Here is a log entry:

10/30 18:42:27  sndc addr unit       4 : hu C4  (kitchen_dining_light)
10/30 18:42:28  sndc func    StatusReq : hc C
10/30 18:42:28  Poll received unknown value (1 bytes), leading byte = 2
10/30 18:42:28  Poll received unknown value (1 bytes), leading byte = 0
10/30 18:42:28  Poll received unknown value (1 bytes), leading byte = 2a
10/30 18:42:29  rcvi func    StatusOff : hc C

Please note that the three bytes, 0x02 0x00 0x2a, together with an initial 0x5a poll request that can be/supposed to get eaten with the failed status request send operation, these four bytes form a complete, correct transmission from the interface, with the 0x2a byte evidently representing an X10 'address C4' signal, received from the queried module obviously, then followed by the correctly decoded StatusOff.



Here is what the current Heyu maintainer is asking:

Quote
Me having much less experience with X10 hardware than C programming, please let me know what do you, experienced X10/CM11A users, think about it. Should we assume a module is broken if it responds to a status request so prompltly that we have problems with correct handling of this response? Or should we tend to not interprete the CM11A returned 0x5a (poll request) replacing awaited 0x55 (ready) as a send failure indication, thus being more prone to real transmission failures caused by unsolicited incoming signals?

Thanks,
Janusz
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Hybrid Setup?
« Reply #17 on: November 03, 2010, 07:12:16 PM »

Test with an early 2876DB Icon Dimmer Switch.
C4 was assigned address.
Smarthome 1132CU with Smarthome Manager Essentials sending and receiving the commands.

You may notice a Status Request returns two messages.
If not On or Off the second message is a %Dim value.

I have no idea if this has any bearing on what you are seeing.

T: C4 - 6:58:46 PM 11/3/2010
T: COn - 6:58:48 PM 11/3/2010
T: C4 - 6:58:53 PM 11/3/2010
T: CStatus Request - 6:58:55 PM 11/3/2010
R: C4 - 6:58:56 PM 11/3/2010
R: CStatus=On - 6:58:56 PM 11/3/2010
R: C4 - 6:58:57 PM 11/3/2010
R: COn - 6:58:57 PM 11/3/2010
T: C4 - 6:59:05 PM 11/3/2010
T: COff - 6:59:07 PM 11/3/2010
T: C4 - 6:59:11 PM 11/3/2010
T: CStatus Request - 6:59:14 PM 11/3/2010
R: C4 - 6:59:15 PM 11/3/2010
R: CStatus=Off - 6:59:15 PM 11/3/2010
R: C4 - 6:59:16 PM 11/3/2010
R: COff - 6:59:16 PM 11/3/2010
T: C4 - 6:59:27 PM 11/3/2010
T:  23% Preset Dim 6:59:30 PM 11/3/2010
T: C4 - 6:59:34 PM 11/3/2010
T: CStatus Request - 6:59:36 PM 11/3/2010
R: C4 - 6:59:37 PM 11/3/2010
R: CStatus=On - 6:59:38 PM 11/3/2010
R: C4 - 6:59:38 PM 11/3/2010
R: 23% Preset Dim 6:59:39 PM 11/3/2010
Logged

Brandt

  • Hero Member
  • *****
  • Helpful Post Rating: 11
  • Posts: 728
  • Sorry miss, I was giving myself an oil-job.
Re: Hybrid Setup?
« Reply #18 on: November 03, 2010, 07:20:20 PM »

I am trying to figure out i why I get this error only when requesting status from the switch when it is off.
Logged

Brian H

  • Community Organizer
  • Hero Member
  • ***
  • Helpful Post Rating: 305
  • Posts: 13259
Re: Hybrid Setup?
« Reply #19 on: November 03, 2010, 07:25:24 PM »

I don't have any ideas why the off is messed up.
I do know that revisions >5.0 have changes in them as there are manuals for above and below 5.0.

This is what I got when I turned it on; off; brightened and dimmed. Using the local paddles.

R: C4 - 7:18:38 PM 11/3/2010
R: COff - 7:18:39 PM 11/3/2010
R: C4 - 7:18:41 PM 11/3/2010
R: COn - 7:18:41 PM 11/3/2010
R: C4 - 7:18:46 PM 11/3/2010
R: 23% Preset Dim 7:18:47 PM 11/3/2010
R: C4 - 7:18:50 PM 11/3/2010
R: 35% Preset Dim 7:18:50 PM 11/3/2010
« Last Edit: November 03, 2010, 07:36:33 PM by Brian H »
Logged
Pages: 1 [2]
 

X10.com | About X10 | X10 Security Systems | Cameras| Package Deals
© Copyright 2014-2016 X10.com All rights reserved.