I have uploaded HRRBI v1.22 from July 2017 to FileMail where it can be downloaded until 11/11/24. After that I can do it again as needed or email to anyone requesting it. I have some older versions too.
Here's the download link:
https://www.filemail.com/d/ixomytlucllfmrh
- December 03, 2024, 01:00:39 PM
- Welcome, Guest
|
31
on: November 04, 2024, 02:35:25 PM
|
||
| Started by trkeenan - Last post by brobin | ||
|
32
on: November 04, 2024, 01:46:12 PM
|
||
| Started by trkeenan - Last post by GarageHawk | ||
|
Hi,
Thanks for your response. I'm looking for the most recent Firmware load. I think it was HomeRunner RBI, v1.19, 09/04/2014 02:01:05 PM. I could be wrong, but I think 2.18 was the last version of the application software. Can any one confirm? Bill |
||
|
33
on: November 04, 2024, 01:14:23 PM
|
||
| Started by trkeenan - Last post by brobin | ||
|
I have HomeRunner 2.18 if that's helpful. Happy to share it if you need it.
|
||
|
34
on: November 04, 2024, 01:08:26 PM
|
||
| Started by GarageHawk - Last post by GarageHawk | ||
|
I have the following JDS equipment that I would be willing to sell.
1ea. SG-1 Controller w/ telephone board 1ea. I/O Expander 1ea. Infrared Expander We can also repair most JDS HomeRunner X10/Insteon controllers. I would like to obtain the latest HomeRunner Firmware download. Please reply to contact me. Best regards, Bill |
||
|
35
on: November 04, 2024, 12:50:21 PM
|
||
| Started by trkeenan - Last post by GarageHawk | ||
|
I have the following JDS equipment that I would be willing to sell.
1ea. SG-1 Controller w/ telephone board 1ea. I/O Expander 1ea. Infrared Expander We can also repair most JDS HomeRunner X10/Insteon controllers. I would like to obtain the latest HomeRunner Firmware download. Please reply to contact me. Best regards, Bill |
||
|
36
on: October 29, 2024, 07:37:17 AM
|
||
| Started by Marauder2003 - Last post by Tuicemen | ||
|
What you could do prior to needing is power up the new router (while still using the old one) and change every thing but the name in the new router. That way when if you need it you only need to change the name and don't have to guess at settings.
 |
||
|
37
on: October 28, 2024, 10:51:54 AM
|
||
| Started by Marauder2003 - Last post by Marauder2003 | ||
When I switched out my last routers I set it up the same as the old.(same name, password and ip) this saved having to reconfigure all my wifi devices. Well, if the current Netgear dies and I go to my new tp-link I will try that. But it will get confusing.  |
||
|
38
on: October 28, 2024, 08:00:56 AM
|
||
| Started by Marauder2003 - Last post by Tuicemen | ||
|
When I switched out my last routers I set it up the same as the old.(same name, password and ip) this saved having to reconfigure all my wifi devices.
|
||
|
39
on: October 27, 2024, 07:25:06 PM
|
||
| Started by Marauder2003 - Last post by Marauder2003 | ||
|
Well, gave up. Went back to original router and all is fine. New device blocking was not on in the new router. No idea what is wrong.
|
||
|
40
on: October 20, 2024, 11:38:40 PM
|
||
| Started by Marauder2003 - Last post by Marauder2003 | ||
|
Replaced router with a new TP-Link. Using a new WM100. 2.4 and 5g bands have different names. iPad and Galaxy S24 are on the 2.4 band. Scan the QR code on the WM100 and try to connect. The process finds the SSID of the 2.4 band. The name is filled in in the app. I put in the password. And it fails to connect. The WM100 does not show up in the router devices. The iPad and S24 do. Router is set to use WMA2.
On the cell and iPad I have deleted the app, powered down and up and reinstalled the app. What am I missing? |
||